P0335 2008 Toyota Prius Code - Crankshaft Position Sensor 'A' Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2008 Toyota Prius indicates Crankshaft Position Sensor 'A' Circuit .
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2008 Toyota Prius Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2008 Toyota Prius?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2008 Toyota Prius?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2008 Toyota Prius code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2008 Toyota Prius code?
Need more information on how to fix the P0335 2008 Toyota Prius code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2008 Toyota Prius code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2008 Toyota Prius Code
1. What are the common symptoms of OBDII code P0335 in a 2008 Toyota Prius?
The common symptoms of OBDII code P0335 in a 2008 Toyota Prius include engine stalling, rough idling, difficulty starting the engine, and reduced fuel efficiency.
2. What does the OBDII code P0335 indicate in a 2008 Toyota Prius?
OBDII code P0335 in a 2008 Toyota Prius indicates a problem with the Crankshaft Position Sensor 'A' Circuit.
3. What are the possible causes of OBDII code P0335 in a 2008 Toyota Prius?
Possible causes of OBDII code P0335 in a 2008 Toyota Prius include a faulty crankshaft position sensor, damaged wiring or connectors, or issues with the sensor's circuit.
4. How can I diagnose the cause of OBDII code P0335 in my 2008 Toyota Prius?
Diagnosing the cause of OBDII code P0335 in a 2008 Toyota Prius involves checking the crankshaft position sensor's wiring and connectors for damage, testing the sensor's circuit, and potentially replacing the sensor if necessary.
5. Can I continue driving my 2008 Toyota Prius with OBDII code P0335?
It is not recommended to continue driving your 2008 Toyota Prius with OBDII code P0335, as it can lead to further engine damage and potential safety hazards. It is best to address the issue promptly.
6. Is it possible to repair OBDII code P0335 in a 2008 Toyota Prius myself?
While some DIY enthusiasts may be able to replace the crankshaft position sensor themselves, diagnosing and repairing OBDII code P0335 in a 2008 Toyota Prius may require professional automotive expertise.
7. How much does it typically cost to repair OBDII code P0335 in a 2008 Toyota Prius?
The cost to repair OBDII code P0335 in a 2008 Toyota Prius can vary depending on the root cause of the issue, but it generally ranges from $100 to $300 for parts and labor.
8. Will resetting the OBDII code P0335 in my 2008 Toyota Prius make it go away permanently?
Resetting the OBDII code P0335 in a 2008 Toyota Prius may temporarily clear the warning light, but if the underlying issue is not addressed, the code is likely to reappear.
9. How long does it take to repair OBDII code P0335 in a 2008 Toyota Prius?
The time required to repair OBDII code P0335 in a 2008 Toyota Prius can vary depending on the diagnostic process and the extent of the repairs needed. It may take a few hours to a full day.
10. What should I do if OBDII code P0335 keeps coming back in my 2008 Toyota Prius?
If OBDII code P0335 keeps coming back in your 2008 Toyota Prius after repairs, it may indicate a persistent issue that requires further diagnosis by a professional mechanic to identify and resolve.
Discuss the causes and fixes for P0335 2008 Toyota Prius OBDII Code
Code P0335 2008 Toyota Prius comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
