P0335 2008 Nissan Xterra Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2008 Nissan Xterra indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2008 Nissan Xterra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2008 Nissan Xterra?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2008 Nissan Xterra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
2005 Xterra Crankshaft Position Sensor Replacement
User Submitted Video
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2008 Nissan Xterra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2008 Nissan Xterra code?
Need more information on how to fix the P0335 2008 Nissan Xterra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2008 Nissan Xterra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2008 Nissan Xterra Code
1. What does OBDII code P0335 mean for a 2008 Nissan Xterra?
The OBDII code P0335 in a 2008 Nissan Xterra indicates a problem with the crankshaft position sensor circuit.
2. What are common symptoms of a P0335 code in a 2008 Nissan Xterra?
Common symptoms of a P0335 code in a 2008 Nissan Xterra include engine stalling, rough idling, difficulty starting the vehicle, and a decrease in fuel efficiency.
3. What are possible causes of a P0335 code in a 2008 Nissan Xterra?
Possible causes of a P0335 code in a 2008 Nissan Xterra include a faulty crankshaft position sensor, damaged wiring or connectors related to the sensor, or issues with the sensor's alignment or installation.
4. How can I diagnose a P0335 code in a 2008 Nissan Xterra?
Diagnosing a P0335 code in a 2008 Nissan Xterra involves using an OBDII scanner to retrieve the code, inspecting the crankshaft position sensor and its wiring for damage, and testing the sensor's functionality using a multimeter.
5. Can I still drive my 2008 Nissan Xterra with a P0335 code?
It is not recommended to drive your 2008 Nissan Xterra with a P0335 code as it can lead to further engine damage and potential safety hazards. It is best to address the issue promptly.
6. How do I repair a P0335 code in my 2008 Nissan Xterra?
To repair a P0335 code in a 2008 Nissan Xterra, you may need to replace the crankshaft position sensor, repair or replace damaged wiring or connectors, and ensure proper alignment and installation of the sensor.
7. Can a DIYer fix a P0335 code in a 2008 Nissan Xterra?
Depending on your skill level and access to tools, a DIYer may be able to fix a P0335 code in a 2008 Nissan Xterra by following repair guides and instructions. However, if unsure, it's best to seek professional help.
8. How much does it cost to fix a P0335 code in a 2008 Nissan Xterra?
The cost to fix a P0335 code in a 2008 Nissan Xterra can vary depending on the root cause of the issue, parts needed for repair, and labor costs. It's advisable to get quotes from mechanics for an accurate estimate.
9. Will resetting the OBDII code make the P0335 issue go away in a 2008 Nissan Xterra?
Resetting the OBDII code may temporarily clear the warning light, but it will not fix the underlying issue causing the P0335 code in a 2008 Nissan Xterra. It's important to diagnose and address the root cause of the problem.
10. How long does it take to repair a P0335 code in a 2008 Nissan Xterra?
The time to repair a P0335 code in a 2008 Nissan Xterra can vary based on the complexity of the issue and the availability of parts. Typically, it may take a few hours to a day for a professional mechanic to diagnose and repair the problem.
Discuss the causes and fixes for P0335 2008 Nissan Xterra OBDII Code
Code P0335 2008 Nissan Xterra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
