P0335 2008 Nissan Sentra Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2008 Nissan Sentra indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2008 Nissan Sentra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2008 Nissan Sentra?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2008 Nissan Sentra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2008 Nissan Sentra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2008 Nissan Sentra code?
Need more information on how to fix the P0335 2008 Nissan Sentra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2008 Nissan Sentra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2008 Nissan Sentra Code
1. What are the common symptoms of OBDII code P0335 in a 2008 Nissan Sentra?
The common symptoms of code P0335 on a 2008 Nissan Sentra include engine stalling, difficulty starting the engine, and poor acceleration.
2. What is the main cause of OBDII code P0335 in a 2008 Nissan Sentra?
The main cause of code P0335 in a 2008 Nissan Sentra is often a faulty crankshaft position sensor or issues with the sensor circuit.
3. How can I diagnose a faulty crankshaft position sensor in my 2008 Nissan Sentra?
To diagnose a faulty crankshaft position sensor in your 2008 Nissan Sentra, you can use a multimeter to check the sensor's resistance and voltage output, as well as inspect the sensor for physical damage.
4. Can a bad crankshaft position sensor cause OBDII code P0335 in a 2008 Nissan Sentra?
Yes, a malfunctioning or failed crankshaft position sensor can trigger OBDII code P0335 in a 2008 Nissan Sentra due to the sensor's crucial role in engine timing and operation.
5. What are some repair tips for fixing OBDII code P0335 in a 2008 Nissan Sentra?
Repair tips for addressing code P0335 on a 2008 Nissan Sentra include replacing the crankshaft position sensor, checking and repairing any damaged wiring or connectors in the sensor circuit, and performing a thorough inspection of related components.
6. Can a DIY enthusiast fix OBDII code P0335 on a 2008 Nissan Sentra?
A DIY enthusiast can potentially fix code P0335 on a 2008 Nissan Sentra by replacing the crankshaft position sensor and conducting basic diagnostic tests, but complex electrical issues may require professional assistance.
7. Is it safe to continue driving with OBDII code P0335 in a 2008 Nissan Sentra?
It is not recommended to continue driving with OBDII code P0335 in a 2008 Nissan Sentra as it can lead to more severe engine problems, such as complete engine failure or further damage to engine components.
8. How much does it typically cost to repair OBDII code P0335 in a 2008 Nissan Sentra?
The cost to repair OBDII code P0335 in a 2008 Nissan Sentra can vary depending on the extent of the issue, but it generally ranges from $100 to $300 for parts and labor.
9. Are there any recalls or technical service bulletins related to OBDII code P0335 in a 2008 Nissan Sentra?
It's advisable to check with Nissan or a certified dealership for any recalls or technical service bulletins related to OBDII code P0335 in a 2008 Nissan Sentra, as manufacturers may provide assistance for known issues.
10. How long does it typically take to repair OBDII code P0335 in a 2008 Nissan Sentra?
The repair time for OBDII code P0335 in a 2008 Nissan Sentra can vary based on the extent of the issue and the technician's expertise, but it usually takes around 1-2 hours to complete the repair.
Discuss the causes and fixes for P0335 2008 Nissan Sentra OBDII Code
Code P0335 2008 Nissan Sentra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
