P0335 2008 Honda Accord Code - Crankshaft Position Sensor 'A' No Signal
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2008 Honda Accord indicates Crankshaft Position Sensor 'A' No Signal.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2008 Honda Accord Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2008 Honda Accord?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2008 Honda Accord?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2008 Honda Accord code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2008 Honda Accord code?
Need more information on how to fix the P0335 2008 Honda Accord code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2008 Honda Accord code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2008 Honda Accord Code
1. What are the common symptoms of OBDII code P0335 on a 2008 Honda Accord?
The common symptoms include engine stalling, rough idling, difficulty starting the vehicle, and a decrease in fuel efficiency.
2. What does the OBDII code P0335 indicate on a 2008 Honda Accord?
OBDII code P0335 indicates a problem with the Crankshaft Position Sensor 'A' not sending a signal to the engine control module.
3. What are the possible causes of OBDII code P0335 on a 2008 Honda Accord?
The possible causes include a faulty crankshaft position sensor, damaged sensor wiring, poor electrical connections, or a problem with the engine control module.
4. How can I diagnose the issue causing OBDII code P0335 on my 2008 Honda Accord?
Diagnosing the issue involves checking the crankshaft position sensor's wiring and connections, testing the sensor itself, and scanning the engine control module for any related fault codes.
5. Can a faulty crankshaft position sensor be repaired, or does it need to be replaced?
In most cases, a faulty crankshaft position sensor will need to be replaced to resolve the issue with OBDII code P0335.
6. Are there any repair tips for fixing OBDII code P0335 on a 2008 Honda Accord?
When replacing the crankshaft position sensor, make sure to use a high-quality OEM or aftermarket sensor to ensure proper functionality.
7. Is it safe to continue driving my 2008 Honda Accord with OBDII code P0335 present?
It is not recommended to continue driving the vehicle with OBDII code P0335 present, as it can lead to further engine problems and potential safety issues.
8. How much does it typically cost to repair OBDII code P0335 on a 2008 Honda Accord?
The cost of repairing OBDII code P0335 can vary depending on the labor rates and parts prices in your area, but it generally ranges from $100 to $300.
9. Can I reset the OBDII code P0335 on my 2008 Honda Accord using an OBDII scanner?
Yes, you can use an OBDII scanner to reset the code after repairing the underlying issue to see if it reoccurs.
10. Will fixing OBDII code P0335 improve the overall performance of my 2008 Honda Accord?
Fixing OBDII code P0335 can improve engine performance, fuel efficiency, and overall drivability of your 2008 Honda Accord.
Discuss the causes and fixes for P0335 2008 Honda Accord OBDII Code
Code P0335 2008 Honda Accord comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
