P0335 2006 Toyota Highlander Code - Crankshaft Position Sensor 'A' Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2006 Toyota Highlander indicates Crankshaft Position Sensor 'A' Circuit .
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2006 Toyota Highlander Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2006 Toyota Highlander?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2006 Toyota Highlander?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2006 Toyota Highlander code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2006 Toyota Highlander code?
Need more information on how to fix the P0335 2006 Toyota Highlander code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2006 Toyota Highlander code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2006 Toyota Highlander Code
1. What does the OBDII code P0335 mean on a 2006 Toyota Highlander?
P0335 indicates an issue with the Crankshaft Position Sensor 'A' Circuit, meaning the engine control module (ECM) is not receiving a proper signal from the sensor.
2. What are the symptoms of a P0335 code on a 2006 Toyota Highlander?
Common symptoms include difficulty starting the engine, rough idling, stalling, reduced engine performance, and the check engine light turning on.
3. What causes a P0335 code on a 2006 Toyota Highlander?
Potential causes include a faulty crankshaft position sensor, damaged wiring or connectors, a failed sensor reluctor ring, or issues with the ECM.
4. How do I fix a P0335 code on my 2006 Toyota Highlander?
Inspect and repair any damaged wiring or connectors, replace the crankshaft position sensor if faulty, and check the reluctor ring for damage or misalignment.
5. Can I drive my 2006 Toyota Highlander with a P0335 code?
Driving with this code is not recommended as it can lead to poor engine performance, stalling, or even complete engine failure, potentially causing unsafe conditions.
6. Where is the crankshaft position sensor located on a 2006 Toyota Highlander?
The crankshaft position sensor is typically located near the bottom of the engine, close to the crankshaft pulley or flywheel.
7. How much does it cost to fix a P0335 code on a 2006 Toyota Highlander?
The cost to replace a crankshaft position sensor typically ranges from $150 to $300, depending on parts and labor rates in your area.
8. Can a dead battery cause a P0335 code on a 2006 Toyota Highlander?
While unlikely, a weak or dead battery can sometimes cause electrical issues that may trigger this code. Ensure the battery and charging system are in good condition.
9. How do I diagnose a P0335 code on a 2006 Toyota Highlander?
Use an OBDII scanner to confirm the code, inspect the crankshaft position sensor and its wiring for visible damage, and test the sensor with a multimeter to verify functionality.
10. Will clearing the P0335 code fix the issue on my 2006 Toyota Highlander?
Clearing the code may temporarily turn off the check engine light, but the issue will persist until the underlying problem is properly addressed.
Discuss the causes and fixes for P0335 2006 Toyota Highlander OBDII Code
Code P0335 2006 Toyota Highlander comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
