P0335 2005 Toyota Highlander Code - Crankshaft Position Sensor 'A' Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2005 Toyota Highlander indicates Crankshaft Position Sensor 'A' Circuit .
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2005 Toyota Highlander Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2005 Toyota Highlander?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2005 Toyota Highlander?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2005 Toyota Highlander code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2005 Toyota Highlander code?
Need more information on how to fix the P0335 2005 Toyota Highlander code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2005 Toyota Highlander code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2005 Toyota Highlander Code
1. What are the common symptoms of OBDII code P0335 in a 2005 Toyota Highlander?
- Common symptoms include engine stalling, rough idling, difficulty starting, and a decrease in fuel efficiency.
2. What does the OBDII code P0335 indicate in a 2005 Toyota Highlander?
- OBDII code P0335 indicates a problem with the crankshaft position sensor 'A' circuit in the vehicle.
3. What are the possible causes of OBDII code P0335 in a 2005 Toyota Highlander?
- Possible causes include a faulty crankshaft position sensor, damaged wiring or connectors in the sensor circuit, or issues with the sensor's alignment.
4. How can I diagnose the issue causing OBDII code P0335 in my 2005 Toyota Highlander?
- You can use a diagnostic scanner to read the code, visually inspect the sensor and its wiring for damage, and perform a resistance test on the sensor.
5. Can I drive my 2005 Toyota Highlander with OBDII code P0335?
- It is not recommended to drive the vehicle with OBDII code P0335, as it can lead to further engine damage or unexpected stalling.
6. How can I repair OBDII code P0335 in my 2005 Toyota Highlander?
- The most common repair is to replace the crankshaft position sensor. Ensure proper alignment and secure wiring connections during the replacement process.
7. Is it possible to reset OBDII code P0335 in a 2005 Toyota Highlander without fixing the issue?
- Resetting the code without fixing the underlying issue will likely result in the code reappearing once the vehicle is driven again.
8. How much does it cost to repair OBDII code P0335 in a 2005 Toyota Highlander?
- The cost of repairs can vary depending on the labor rates and parts prices, but replacing the crankshaft position sensor typically ranges from $100 to $300.
9. Can a DIY enthusiast fix OBDII code P0335 in a 2005 Toyota Highlander?
- Yes, if you have the necessary tools and experience, you can replace the crankshaft position sensor yourself following detailed instructions or a repair manual.
10. Are there any preventive measures to avoid OBDII code P0335 in a 2005 Toyota Highlander?
- Regular maintenance, including checking the sensor wiring for wear and tear, can help prevent issues with the crankshaft position sensor and potentially avoid OBDII code P0335.
Discuss the causes and fixes for P0335 2005 Toyota Highlander OBDII Code
Code P0335 2005 Toyota Highlander comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
