P0335 2004 Nissan Altima Sedan Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2004 Nissan Altima Sedan indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2004 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2004 Nissan Altima Sedan?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2004 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2004 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2004 Nissan Altima Sedan code?
Need more information on how to fix the P0335 2004 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2004 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2004 Nissan Altima Sedan Code
1. What are the common symptoms of OBDII code P0335 in a 2004 Nissan Altima Sedan?
The common symptoms of P0335 include difficulty starting the vehicle, engine misfires, rough idling, and stalling.
2. What is the main cause of OBDII code P0335 in a 2004 Nissan Altima Sedan?
The main cause of code P0335 in a 2004 Nissan Altima Sedan is a faulty crankshaft position sensor or an issue with the sensor circuit.
3. How does a faulty crankshaft position sensor affect the performance of a 2004 Nissan Altima Sedan?
A faulty crankshaft position sensor can cause inaccurate timing signals to be sent to the engine control module, leading to poor engine performance and potential stalling.
4. Can a DIY enthusiast replace the crankshaft position sensor in a 2004 Nissan Altima Sedan to address code P0335?
Yes, replacing the crankshaft position sensor in a 2004 Nissan Altima Sedan can be a DIY project, but it requires basic mechanical skills and the right tools.
5. Are there any tips to keep in mind when replacing the crankshaft position sensor in a 2004 Nissan Altima Sedan?
When replacing the crankshaft position sensor, make sure to disconnect the battery, follow the manufacturer's instructions, and test the new sensor after installation.
6. How much does it typically cost to repair OBDII code P0335 in a 2004 Nissan Altima Sedan at a professional mechanic's shop?
The cost of repairing P0335 at a mechanic's shop can vary but generally ranges from $150 to $300, depending on labor rates and the cost of parts.
7. Can driving with OBDII code P0335 in a 2004 Nissan Altima Sedan cause further damage to the vehicle?
Continued driving with code P0335 can potentially lead to more severe engine issues, such as engine stalling or complete engine failure, so it's best to address the problem promptly.
8. Is it safe to clear the OBDII code P0335 in a 2004 Nissan Altima Sedan without fixing the underlying issue?
Clearing the code without fixing the underlying issue will only temporarily remove the warning light, but the problem will likely resurface, and potential engine issues may worsen over time.
9. How important is the crankshaft position sensor in a 2004 Nissan Altima Sedan's overall engine performance?
The crankshaft position sensor is crucial for providing accurate engine timing information, so a faulty sensor can negatively impact the overall performance and reliability of the vehicle.
10. Can a bad crankshaft position sensor in a 2004 Nissan Altima Sedan cause the car to suddenly shut off while driving?
Yes, a malfunctioning crankshaft position sensor can cause the engine to shut off unexpectedly while driving, posing a safety risk.
Discuss the causes and fixes for P0335 2004 Nissan Altima Sedan OBDII Code
Code P0335 2004 Nissan Altima Sedan comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
