P0328 2016 Toyota RAV4 Code - Knock Sensor 1 Circuit High Input
Quick Answer
A flat-type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz. Common causes include Faulty Knock Sensor, Knock Sensor circuit poor electrical connection, Knock Sensor harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0328 2016 Toyota RAV4 indicates Knock Sensor 1 Circuit High Input.
- Common causes
- Common causes include Faulty Knock Sensor, Knock Sensor circuit poor electrical connection, Knock Sensor harness is open or shorted.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0328 2016 Toyota RAV4 Description
If the output voltage transmitted by the knock control sensor remains low or high for 1 second or more, the Engine Control Module (ECM) interprets this as a malfunction in the sensor circuit and stores a Diagnostic Trouble Code (DTC).
What are the Possible Causes of the DTC P0328 2016 Toyota RAV4?
- Faulty Knock Sensor
- Knock Sensor circuit poor electrical connection
- Knock Sensor harness is open or shorted
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0328 2016 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0328 2016 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0328 2016 Toyota RAV4 code?
Need more information on how to fix the P0328 2016 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0328 2016 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0328 2016 Toyota RAV4 Code
1. What does the OBDII code P0328 mean for a 2016 Toyota RAV4?
The P0328 code indicates that the Knock Sensor 1 in Bank 1 has a high input, meaning the sensor is detecting a signal outside the expected range.
2. What are the symptoms of P0328 in a 2016 Toyota RAV4?
Common symptoms include illuminated Check Engine Light, reduced engine performance, poor fuel economy, and in some cases, engine knocking or pinging.
3. What causes the P0328 code in a 2016 Toyota RAV4?
Potential causes include a faulty knock sensor, damaged wiring or connectors, an engine overheating issue, or a problem with the vehicle’s ECU.
4. Is it safe to drive a 2016 Toyota RAV4 with a P0328 code?
While the car may still be drivable, ignoring the issue can lead to poor performance and potential engine damage over time due to improper ignition timing.
5. How do I diagnose the P0328 code on my 2016 Toyota RAV4?
Start by checking the knock sensor wiring and connectors for damage, inspect the sensor itself, and use a multimeter to test its resistance. You may also need a scan tool to monitor live data.
6. How do I fix the P0328 code on a 2016 Toyota RAV4?
Repairs may include replacing the knock sensor, repairing damaged wiring or connectors, addressing overheating issues, or reprogramming the ECU if necessary.
7. Can a bad knock sensor cause engine damage in a 2016 Toyota RAV4?
Yes, a malfunctioning knock sensor can prevent the ECU from properly adjusting ignition timing, which may lead to engine knocking and potential long-term damage.
8. How much does it cost to repair a P0328 code in a 2016 Toyota RAV4?
The repair cost depends on the issue, but replacing a knock sensor typically ranges from $150 to $500, including parts and labor.
9. Can I reset the P0328 code without fixing the issue?
You can clear the code with an OBDII scanner, but it will likely return unless the underlying problem is resolved.
10. What tools are needed to fix the P0328 code on a 2016 Toyota RAV4?
You’ll need an OBDII scanner, a multimeter for testing the sensor and wiring, and basic hand tools to access and replace the knock sensor if needed.
Discuss the causes and fixes for P0328 2016 Toyota RAV4 OBDII Code
Code P0328 2016 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
