P0320 Jeep Code - No Crank Reference Signal At PCM
Quick Answer
The Crankshaft Position Sensor (CKP) is mounted to the transmission bellhousing at the left"rear side of the engine block. Common causes include Faulty Crankshaft Position Sensor (CKP), Crankshaft Position Sensor (CKP) harness is open or shorted, Crankshaft Position Sensor (CKP) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0320 Jeep indicates No Crank Reference Signal At PCM.
- Common causes
- Common causes include Faulty Crankshaft Position Sensor (CKP), Crankshaft Position Sensor (CKP) harness is open or shorted, Crankshaft Position Sensor (CKP) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0320 Jeep Description
Engine speed and crankshaft position are provided through the crankshaft position sensor. The sensor generates pulses that are the input sent to the Powertrain Control Module (PCM). The PCM interprets the sensor input to determine the crankshaft position. The PCM then uses this position, along with other inputs, to determine injector sequence and ignition timing.
The sensor is a hall effect device combined with an internal magnet. It is also sensitive to steel within a certain distance from it.
What are the Possible Causes of the DTC P0320 Jeep?
- Faulty Crankshaft Position Sensor (CKP)
- Crankshaft Position Sensor (CKP) harness is open or shorted
- Crankshaft Position Sensor (CKP) circuit poor electrical connection
- Faulty Powertrain Control Module (PCM)
How to Fix the DTC P0320 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0320 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0320 Jeep code?
Need more information on how to fix the P0320 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0320 Jeep code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0320 Jeep Code
1. What does the OBDII code P0320 mean on a Jeep?
P0320 indicates that the Powertrain Control Module (PCM) is not receiving a proper crankshaft position signal, which is necessary for ignition timing and fuel delivery.
2. What are the common symptoms of the P0320 code on a Jeep?
Symptoms include engine stalling, difficulty starting, a no-start condition, rough idling, and the Check Engine Light being illuminated.
3. What causes the P0320 code to appear on a Jeep?
Common causes include a malfunctioning crankshaft position sensor, faulty wiring or connectors, a damaged PCM, or issues with the ignition system.
4. Can a bad camshaft position sensor trigger the P0320 code on a Jeep?
Yes, since the PCM uses signals from both the crankshaft and camshaft position sensors, a faulty camshaft position sensor can sometimes contribute to this code.
5. How do I fix the P0320 code on my Jeep?
Start by inspecting the crankshaft position sensor, its wiring, and connectors for damage. Replace the sensor if necessary. If the issue persists, check the PCM and ignition system for faults.
6. Can I drive my Jeep with the P0320 code active?
While the vehicle may still run, driving with this code can lead to engine stalling or a no-start condition, potentially leaving you stranded. It’s best to address it promptly.
7. How do I test the crankshaft position sensor on a Jeep?
You can use a multimeter to test the sensor’s resistance or monitor its signal with an OBDII scanner while cranking the engine. Compare the readings to manufacturer specifications.
8. Is replacing the PCM necessary to fix the P0320 code on a Jeep?
PCM replacement is rarely needed. Only consider replacing it after verifying that the crankshaft position sensor, wiring, and connectors are functioning properly.
9. What tools are needed to diagnose the P0320 code on a Jeep?
Tools like an OBDII scanner, a multimeter, and basic hand tools are typically required for diagnosing and repairing this code.
10. What is the cost to fix the P0320 code on a Jeep?
Repair costs vary but generally range from $100 to $300 for parts and labor, depending on whether the crankshaft position sensor or other components need replacement.
Discuss the causes and fixes for P0320 Jeep OBDII Code
Code P0320 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
