P0306 2007 Ford Fusion Code - Cylinder 6 Misfire Detected
Quick Answer
Misfire is defined as a lack of combustion in a cylinder due to the absence of a spark, incorrect fuel metering, low compression, or any other cause. Common causes include Faulty spark plug 6, Clogged or faulty fuel injector 6, Faulty ignition coil 6. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0306 2007 Ford Fusion indicates Cylinder 6 Misfire Detected.
- Common causes
- Common causes include Faulty spark plug 6, Clogged or faulty fuel injector 6, Faulty ignition coil 6.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0306 2007 Ford Fusion Description
When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the Crankshaft Position (CKP) sensor signal to vary, the Engine Control Module (ECM) can determine that a misfire is occurring.
The Malfunction Indicator Lamp (MIL) blinks once per second when detecting a misfire severe enough to cause catalyst damage. If the MIL is in a steady state due to a misfire, this indicates the threshold for emissions was exceeded and caused the vehicle to fail an inspection and maintenance tailpipe test.
This Diagnostic Trouble Code (DTC) sets when the misfire detection monitor detects an engine misfire in cylinder 6.
What are the Possible Causes of the DTC P0306 2007 Ford Fusion?
- Faulty spark plug 6
- Clogged or faulty fuel injector 6
- Faulty ignition coil 6
- Fuel injector 6 harness is open or shorted
- Fuel injector 6 circuit poor electrical connection
- Ignition coil 6 harness is open or shorted
- Ignition coil 6 circuit poor electrical connection
- Insufficient cylinder 6 compression
- Incorrect fuel pressure
- Intake air leak
How to Fix the DTC P0306 2007 Ford Fusion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0306 2007 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0306 2007 Ford Fusion code?
Need more information on how to fix the P0306 2007 Ford Fusion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0306 2007 Ford Fusion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0306 2007 Ford Fusion Code
1. What does the OBDII code P0306 mean on a 2007 Ford Fusion?
P0306 indicates that the engine’s computer has detected a misfire in cylinder 6.
2. What are the common symptoms of a P0306 code in a 2007 Ford Fusion?
Symptoms may include rough idling, reduced power, poor fuel economy, hesitation during acceleration, or the check engine light turning on.
3. What causes a cylinder 6 misfire in a 2007 Ford Fusion?
Common causes include a faulty spark plug, ignition coil, fuel injector, vacuum leak, low compression, or issues with the engine control module (ECM).
4. Can I drive my 2007 Ford Fusion with a P0306 code?
Driving with a P0306 code is not recommended as it may cause engine damage or lead to unsafe driving conditions due to reduced performance.
5. How do I fix the P0306 code on a 2007 Ford Fusion?
Start by inspecting and replacing the spark plug or ignition coil for cylinder 6. If the issue persists, check the fuel injector, wiring, and engine compression.
6. How do I identify cylinder 6 on a 2007 Ford Fusion?
Cylinder 6 is located on the rear bank (firewall side) of the engine, typically the last cylinder in the firing order.
7. Can a vacuum leak cause a P0306 code in a 2007 Ford Fusion?
Yes, a vacuum leak near cylinder 6 can disrupt the air/fuel mixture and cause a misfire.
8. What tools do I need to diagnose a P0306 code on a 2007 Ford Fusion?
You’ll need an OBDII scanner, a spark plug socket, a multimeter, and possibly a compression tester to diagnose the issue accurately.
9. How much does it cost to fix a P0306 code on a 2007 Ford Fusion?
The repair cost varies but typically ranges from $100 to $300 for parts and labor, depending on whether it’s a spark plug, ignition coil, or fuel injector issue.
10. Can a clogged fuel injector cause a P0306 code in a 2007 Ford Fusion?
Yes, a clogged or malfunctioning fuel injector can prevent proper fuel delivery to cylinder 6, leading to a misfire.
Discuss the causes and fixes for P0306 2007 Ford Fusion OBDII Code
Code P0306 2007 Ford Fusion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
