AutoCodes - Toyota - P0304 2008 TOYOTA CAMRY

P0304 2008 TOYOTA CAMRY Code - Cylinder 4 Misfire Detected

Repair Importance Level: 3/3
Repair Difficulty Level: 3/3
Table of contents

|P0304 2008 TOYOTA CAMRY code possible causes

  • Faulty spark plug 4
  • Clogged or faulty fuel injector 4
  • Faulty ignition coil 4
  • Fuel injector 4 harness is open or shorted
  • Fuel injector 4 circuit poor electrical connection
  • Ignition coil 4 harness is open or shorted
  • Ignition coil 4 circuit poor electrical connection
  • Insufficient cylinder 4 compression
  • Incorrect fuel pressure
  • Intake air leak

|How do I fix the P0304 2008 TOYOTA CAMRY code?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

|P0304 2008 TOYOTA CAMRY code tech notes

The P0304 code means that the cylinder 4 is misfiring or is randomly misfiring. Start by checking for intake leaks and if no leaks are found the next step is to replace the spark plugs on cylinder 4. If the problem persists more tests needs to be done to diagnose problem, see "Possible Causes"

|Cost of diagnosing the P0304 2008 TOYOTA CAMRY code

Labor: 1.0

The cost of diagnosing the P0304 2008 TOYOTA CAMRY code is 1.0 hour of labor. The auto repair's diagnosis time and labor rates vary by location, vehicle's make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

|When is the P0304 2008 TOYOTA CAMRY code detected?

Engine Cylinder 4 is Misfiring.

|What are P0304 2008 TOYOTA CAMRY code possible symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)
  • Lack/loss of power
  • Hard start
  • Engine hesitation

|P0304 2008 TOYOTA CAMRY code description

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire rate exceeds the threshold level, and could cause emission deterioration, the ECM illuminates the MIL and sets a DTC.
OBDII Code P0304 2008 Toyota Camry - Cylinder 4 Misfire Detected - AutoCodes.com

|Need more information with the P0304 2008 TOYOTA CAMRY code?

Need more information on how to fix the P0304 2008 TOYOTA CAMRY code? Get Access to Factory Service Manuals

|Need help with a P0304 2008 TOYOTA CAMRY code?

Get the P0304 2008 Toyota Camry code diagnosed by a professional: Find a repair shop in your area

|P0304 2008 TOYOTA CAMRY code comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P0304 2008 Toyota Camry code? Have you replaced any parts?
Any information is appreciated. Thanks
Top ⇧
Repair Importance Level: 3
 
1=Low 2=Medium 3=High What is this?
Repair Difficulty Level: 3
 
1=Easy 2=Moderate 3=Hard What is this?