P0223 2011 Nissan Rogue Code - Throttle Position Sensor 1 Circuit High Input
Quick Answer
Electric Throttle Control Actuator consists of throttle control motor, throttle position sensor (TPS), etc. Common causes include Faulty Throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0223 2011 Nissan Rogue indicates Throttle Position Sensor 1 Circuit High Input.
- Common causes
- Common causes include Faulty Throttle position sensor, Throttle position sensor harness is open or shorted, Throttle position sensor poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0223 2011 Nissan Rogue Description
The throttle position sensor has the two sensors. These sensors are a kind of potentiometers which transform the throttle valve position into output voltage, and emit the voltage signal to the Engine Control Module (ECM) In addition, these sensors detect the opening and closing speed of the throttle valve and feed the voltage signals to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and the ECM controls the throttle control motor to make the throttle valve opening angle properly in response to driving condition.
What are the Possible Causes of the DTC P0223 2011 Nissan Rogue?
- Faulty Throttle position sensor
- Throttle position sensor harness is open or shorted
- Throttle position sensor poor electrical connection
- Faulty accelerator pedal position sensor
How to Fix the DTC P0223 2011 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0223 2011 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0223 2011 Nissan Rogue code?
Need more information on how to fix the P0223 2011 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0223 2011 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0223 2011 Nissan Rogue Code
1. What are the common symptoms of OBDII code P0223 in a 2011 Nissan Rogue?
When the throttle position sensor 1 circuit registers high input, you may experience issues like poor acceleration, reduced engine power, rough idling, and potentially even stalling.
2. What does the OBDII code P0223 indicate in a 2011 Nissan Rogue?
Code P0223 specifically points to a problem with the Throttle Position Sensor 1 Circuit High Input in the vehicle's engine control module.
3. What are the possible causes of OBDII code P0223 in a 2011 Nissan Rogue?
Common causes of the Throttle Position Sensor 1 Circuit High Input error include a faulty throttle position sensor, damaged wiring or connectors in the sensor circuit, or issues with the engine control module itself.
4. How can I diagnose the Throttle Position Sensor 1 Circuit High Input issue in my 2011 Nissan Rogue?
To diagnose the problem, you can use an OBDII scanner to retrieve the specific error code. Additionally, inspect the throttle position sensor and its wiring for any signs of damage or loose connections.
5. Can I continue driving my 2011 Nissan Rogue with OBDII code P0223?
It is not recommended to drive your vehicle with code P0223 as it can lead to further damage and potentially unsafe driving conditions. It's best to address the issue promptly.
6. How can I repair OBDII code P0223 in my 2011 Nissan Rogue?
Repairing code P0223 typically involves replacing the throttle position sensor if it's faulty, repairing any damaged wiring or connectors, and resetting the error code with an OBDII scanner.
7. Is it possible to reset OBDII code P0223 in a 2011 Nissan Rogue without repairing the issue?
While you can clear the error code temporarily, it is crucial to address the root cause of the problem to prevent the code from reappearing and potentially causing more severe issues.
8. Can a DIY enthusiast fix OBDII code P0223 in a 2011 Nissan Rogue?
If you have experience working on automotive electrical systems and access to the necessary tools, you may be able to replace the throttle position sensor or repair wiring yourself. However, professional assistance is recommended for accurate diagnosis and repair.
9. How much does it typically cost to repair OBDII code P0223 in a 2011 Nissan Rogue?
The cost of repairing code P0223 can vary depending on the exact cause of the issue, the labor rates in your area, and whether you choose to replace the throttle position sensor yourself or have it done at a repair shop. It's advisable to obtain quotes from local mechanics for a more accurate estimate.
10. Will fixing OBDII code P0223 improve the performance and fuel efficiency of my 2011 Nissan Rogue?
Yes, addressing the Throttle Position Sensor 1 Circuit High Input issue should lead to improved engine performance, smoother acceleration, and potentially better fuel efficiency in your Nissan Rogue.
Discuss the causes and fixes for P0223 2011 Nissan Rogue OBDII Code
Code P0223 2011 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
