AutoCodes – Ford – P0192 2011 Ford Fusion

P0192 2011 Ford Fusion Code - Fuel Rail Pressure Sensor Circuit Low Input

Quick Answer

The FRP sensor is a diaphragm strain gauge device. Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P0192 2011 Ford Fusion indicates Fuel Rail Pressure Sensor Circuit Low Input.
Common causes: Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 4,189

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Apr 24, 2019

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0192 2011 Ford Fusion Description

The FRP sensor is a diaphragm strain gauge device. The FRP sensor measures the pressure difference between the fuel rail and atmospheric pressure. The FRP sensor nominal output varies between 0.5 and 4.5 volts, with 0.5 volts corresponding to 0 MPa (0 psi) gauge and 4.5 volts corresponding to 26 MPa (3771 psi) gauge. The sensor can read vacuums and may lower the output voltage to slightly below 0.5 volts. This condition is normal and is usually the case after several hours of cold soak before the vehicle dome light is turned on. The FP module is energized at the same time the dome light is commanded on. A disabled or malfunctioning dome light does not affect the FP module control.
The FRP sensor is located on the fuel rail, and provides a feedback signal to indicate the fuel rail pressure to the Powertrain Control Module (PCM). The PCM uses the FRP signal to command the correct injector timing and pulse width for correct fuel delivery at all speed and load conditions. The FRP sensor, along with the fuel volume regulator (part of the fuel injection pump), form a closed loop fuel pressure control system. An electrically faulted FRP sensor results in the deactivation of the fuel injection pump. Fuel pressure to injectors is then provided only by the FP module. When the fuel injection pump is de-energized and the injectors are active, the fuel rail pressure is approximately 70 kPa (10 psi) lower than FP module pressure due to the pressure drop across the fuel injection pump. Thus, if the FP module pressure is 448 kPa (65 psi), then the fuel rail pressure would be approximately 379 kPa (55 psi) if the injectors are active.

OBDII Code P0192 2011 Ford Fusion - Fuel Rail Pressure Sensor Circuit Low Input - AutoCodes.com — P0192 2011 Ford Fusion Code - Fuel Rail Pressure Sensor Circuit Low Input

What does this mean?

What are the Possible Causes of the DTC P0192 2011 Ford Fusion?

Low or no fuel
Faulty Rail Pressure (FRP) Sensor
FRP harness is open or shorted
FRP circuit poor electrical connection
Faulty Fuel Pump

How to Fix the DTC P0192 2011 Ford Fusion?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0192 2011 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0192 2011 Ford Fusion code?

Need more information on how to fix the P0192 2011 Ford Fusion code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0192 2011 Ford Fusion code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0192 2011 Ford Fusion Code

What does the OBDII code P0192 mean for a 2011 Ford Fusion?

P0192 indicates that the fuel rail pressure sensor circuit is reading a low input, which means the Engine Control Module (ECM) is not receiving the expected voltage from the fuel rail pressure sensor.

What are common symptoms of the P0192 code?

Common symptoms include poor engine performance, rough idling, stalling, decreased fuel efficiency, and the check engine light illuminating.

What could cause the P0192 code to trigger?

Potential causes include a faulty fuel rail pressure sensor, damaged wiring or electrical connectors, a bad ECM, or issues with the fuel system such as low fuel pressure.

How can I diagnose a P0192 code?

To diagnose the P0192 code, check the fuel rail pressure sensor and its wiring for any damage, test the sensor's output voltage with a multimeter, and ensure the fuel system is operating correctly.

What are the potential effects of ignoring the P0192 code?

Ignoring the P0192 code can lead to poor engine performance, potential engine damage, decreased fuel efficiency, and could result in further trouble codes being triggered.

How can I fix the P0192 code?

Fixing the P0192 code typically involves inspecting and repairing any damaged wiring or connectors, replacing the fuel rail pressure sensor if it's faulty, and ensuring proper fuel system operation.

Is it safe to drive with the P0192 code?

While it may be possible to drive with the P0192 code, it is not recommended as it can lead to performance issues and potential engine damage over time.

Can I clear the P0192 code without fixing the problem?

You can clear the code using an OBDII scanner, but the code will likely return if the underlying issue is not resolved.

What is the average cost to repair the P0192 issue?

Repair costs can vary widely depending on the cause, but replacing the fuel rail pressure sensor typically ranges from $100 to $300, including parts and labor.