AutoCodes – Ford – P0192 1998 Ford F150

P0192 1998 Ford F150 Code - Fuel Rail Pressure Sensor Circuit Low Input

Quick Answer

The FRP sensor is a diaphragm strain gauge device. Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P0192 1998 Ford F150 indicates Fuel Rail Pressure Sensor Circuit Low Input.
Common causes: Common causes include Low or no fuel, Faulty Rail Pressure (FRP) Sensor, FRP harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 2,617

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 30, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0192 1998 Ford F150 Description

The FRP sensor is a diaphragm strain gauge device. The FRP sensor measures the pressure difference between the fuel rail and atmospheric pressure. The FRP sensor nominal output varies between 0.5 and 4.5 volts, with 0.5 volts corresponding to 0 MPa (0 psi) gauge and 4.5 volts corresponding to 26 MPa (3771 psi) gauge. The sensor can read vacuums and may lower the output voltage to slightly below 0.5 volts. This condition is normal and is usually the case after several hours of cold soak before the vehicle dome light is turned on. The FP module is energized at the same time the dome light is commanded on. A disabled or malfunctioning dome light does not affect the FP module control.
The FRP sensor is located on the fuel rail, and provides a feedback signal to indicate the fuel rail pressure to the Powertrain Control Module (PCM). The PCM uses the FRP signal to command the correct injector timing and pulse width for correct fuel delivery at all speed and load conditions. The FRP sensor, along with the fuel volume regulator (part of the fuel injection pump), form a closed loop fuel pressure control system. An electrically faulted FRP sensor results in the deactivation of the fuel injection pump. Fuel pressure to injectors is then provided only by the FP module. When the fuel injection pump is de-energized and the injectors are active, the fuel rail pressure is approximately 70 kPa (10 psi) lower than FP module pressure due to the pressure drop across the fuel injection pump. Thus, if the FP module pressure is 448 kPa (65 psi), then the fuel rail pressure would be approximately 379 kPa (55 psi) if the injectors are active.

OBDII Code P0192 1998 Ford F150 - Fuel Rail Pressure Sensor Circuit Low Input - AutoCodes.com — P0192 1998 Ford F150 Code - Fuel Rail Pressure Sensor Circuit Low Input

What does this mean?

What are the Possible Causes of the DTC P0192 1998 Ford F150?

Low or no fuel
Faulty Rail Pressure (FRP) Sensor
FRP harness is open or shorted
FRP circuit poor electrical connection
Faulty Fuel Pump

How to Fix the DTC P0192 1998 Ford F150?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The comprehensive component monitor (CCM) monitors the FRP sensor circuit to the PCM for low voltage. If voltage were to fall below a calibrated limit and amount of time during testing, the test will fail.
A FRP PID value during KOER or KOEO less than 0.3 volts for gasoline or 0.5 volts for natural gas vehicles (NG) would indicate a hard fault.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0192 1998 Ford F150 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0192 1998 Ford F150 code?

Need more information on how to fix the P0192 1998 Ford F150 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0192 1998 Ford F150 code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0192 1998 Ford F150 Code

1. What are the common symptoms of OBDII code P0192 on a 1998 Ford F150?

The common symptoms of OBDII code P0192 on a 1998 Ford F150 include poor engine performance, rough idling, stalling, and a decrease in fuel efficiency.

2. What does the OBDII code P0192 indicate on a 1998 Ford F150?

OBDII code P0192 on a 1998 Ford F150 indicates a low input in the fuel rail pressure sensor circuit.

3. What are the possible causes of OBDII code P0192 on a 1998 Ford F150?

Possible causes of OBDII code P0192 on a 1998 Ford F150 include a faulty fuel rail pressure sensor, wiring issues in the sensor circuit, or a problem with the powertrain control module (PCM).

4. How can I diagnose OBDII code P0192 on my 1998 Ford F150?

To diagnose OBDII code P0192 on a 1998 Ford F150, you can use a scan tool to check for the code, inspect the fuel rail pressure sensor and its wiring for any damage, and test the sensor's voltage and resistance.

5. Can I still drive my 1998 Ford F150 with OBDII code P0192?

It is not recommended to drive your 1998 Ford F150 with OBDII code P0192, as it can lead to further damage to the engine and components. It's best to address the issue promptly.

6. Is it safe to reset the OBDII code P0192 on a 1998 Ford F150 and see if it comes back?

While you can reset the code to see if it reoccurs, it is important to address the underlying issue causing OBDII code P0192 on your 1998 Ford F150 to prevent future problems.

7. How much does it typically cost to repair OBDII code P0192 on a 1998 Ford F150?

The cost to repair OBDII code P0192 on a 1998 Ford F150 can vary depending on the exact cause of the issue. Generally, it may range from $100 to $300 for parts and labor.

8. Can a DIY enthusiast fix OBDII code P0192 on a 1998 Ford F150?

A DIY enthusiast with the necessary tools and knowledge of automotive repair may be able to fix OBDII code P0192 on a 1998 Ford F150, especially if the issue is related to wiring or sensor replacement.

9. How urgent is it to address OBDII code P0192 on a 1998 Ford F150?

It is important to address OBDII code P0192 on a 1998 Ford F150 promptly to prevent further damage to the vehicle and ensure optimal engine performance.

10. Will OBDII code P0192 on a 1998 Ford F150 cause the check engine light to illuminate?

Yes, OBDII code P0192 on a 1998 Ford F150 will trigger the check engine light to illuminate as it indicates a problem in the fuel rail pressure sensor circuit.