| All About OBDII Engine Codes
AutoCodes - Ford - P0191 2011 FORD FUSION

P0191 2011 FORD FUSION Code - Fuel Rail Pressure Sensor Circuit Range/Performance

- Code Popularity: 3,724 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
By - Updated Jul 26, 2022
Share on Facebook   Share on Twitter   Share on Linkedin

|P0191 2011 FORD FUSION code possible causes

  • Low or no fuel
  • Faulty Fuel Rail Pressure (FRP) Sensor
  • FRP harness is open or shorted
  • FRP circuit poor electrical connection
  • Faulty Fuel Pump

|How do I fix code P0191 2011 FORD FUSION code?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

Does your car have Safety Recalls? → Check here

|Cost of diagnosing P0191 2011 FORD FUSION code

Labor: 1.0

The cost of diagnosing the P0191 2011 FORD FUSION code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

|What are P0191 2011 FORD FUSION code possible symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)
  • Engine will not start

|P0191 2011 FORD FUSION code description

The Fuel Rail Pressure (FRP) Sensor is a diaphragm strain gauge device. The FRP sensor measures the pressure difference between the fuel rail and atmospheric pressure. The FRP sensor nominal output varies between 0.5 and 4.5 volts, with 0.5 volts corresponding to 0 MPa (0 psi) gauge and 4.5 volts corresponding to 26 MPa (3771 psi) gauge. The sensor can read vacuums and may lower the output voltage to slightly below 0.5 volts. This condition is normal and is usually the case after several hours of cold soak before the vehicle dome light is turned on. The FP module is energized at the same time the dome light is commanded on. A disabled or malfunctioning dome light does not affect the FP module control.
The FRP sensor is located on the fuel rail and provides a feedback signal to indicate the fuel rail pressure to the Powertrain Control Module (PCM). The PCM uses the FRP signal to command the correct injector timing and pulse width for correct fuel delivery at all speed and load conditions. The FRP sensor, along with the fuel volume regulator (part of the fuel injection pump), forms a closed loop fuel pressure control system. An electrically faulted FRP sensor results in the deactivation of the fuel injection pump. Fuel pressure to injectors is then provided only by the FP module. When the fuel injection pump is de-energized and the injectors are active, the fuel rail pressure is approximately 70 kPa (10 psi) lower than FP module pressure due to the pressure drop across the fuel injection pump. Thus, if the FP module pressure is 448 kPa (65 psi), then the fuel rail pressure would be approximately 379 kPa (55 psi) if the injectors are active.

OBDII Code p0191 2011 ford fusion - Fuel Rail Pressure Sensor Circuit Range/Performance -
P0191 2011 FORD FUSION Code - Fuel Rail Pressure Sensor Circuit Range/Performance

|Need more information with the P0191 2011 FORD FUSION code?

Need more information on how to fix the P0191 2011 FORD FUSION code? Get Access to Factory Service Manuals

|Need help with a P0191 2011 FORD FUSION code?

Get the p0191 2011 ford fusion code diagnosed by a professional: Find a repair shop in your area

|P0191 2011 FORD FUSION code comments

Help us improve Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the p0191 2011 ford fusion code? Have you replaced any parts?
Any information is appreciated. Thanks