AutoCodes – Buick – P013D Buick

P013D Buick Code - HO2S Slow Response Lean to Rich Bank 2 Sensor 2

Quick Answer

The Heated Oxygen Sensors (HO2S) are used for fuel control and catalyst monitoring. Common causes include Faulty Heated Oxygen Bank 2 Sensor 2, Heated Oxygen Bank 2 Sensor 2 harness is open or shorted, Heated Oxygen Bank 2 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P013D Buick indicates HO2S Slow Response Lean to Rich Bank 2 Sensor 2.
Common causes: Common causes include Faulty Heated Oxygen Bank 2 Sensor 2, Heated Oxygen Bank 2 Sensor 2 harness is open or shorted, Heated Oxygen Bank 2 Sensor 2 circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 1,474

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 28, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P013D Buick Description

The Heated Oxygen Sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the engine is started, the Engine Control Module (ECM) operates in an Open Loop mode, ignoring the HO2S signal voltage while calculating the air-to-fuel ratio. While the engine runs, the HO2S heats up and begins to generate a voltage within a range of 0 - 1, 000 mV. Once sufficient HO2S voltage fluctuation is observed by the ECM, Closed Loop is entered. The ECM uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1, 000 mV indicates a rich fuel mixture. An HO2S voltage that decreases toward 0 mV indicates a lean fuel mixture.
The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed Loop earlier and the ECM to calculate the air-to-fuel ratio sooner.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects that the accumulated mass airflow monitored during lean-to-rich transitions between 350 - 650 mV is greater than calibrated value.

OBDII Code P013D Buick - HO2S Slow Response Lean to Rich Bank 2 Sensor 2 - AutoCodes.com — P013D Buick Code - HO2S Slow Response Lean to Rich Bank 2 Sensor 2

What does this mean?

What are the Possible Causes of the DTC P013D Buick?

Faulty Heated Oxygen Bank 2 Sensor 2
Heated Oxygen Bank 2 Sensor 2 harness is open or shorted
Heated Oxygen Bank 2 Sensor 2 circuit poor electrical connection
Low or high fuel system pressure
Fuel contamination
Faulty fuel injectors
Exhaust gas leaks
Engine vacuum leaks

How to Fix the DTC P013D Buick?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

Replacing the Rear Heated Oxygen Sensors (HO2S) usually takes care of the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P013D Buick code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P013D Buick code?

Need more information on how to fix the P013D Buick code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P013D Buick code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P013D Buick Code

1. What are the common symptoms of OBDII code P013D in a Buick?

- Common symptoms include reduced fuel efficiency, rough idling, engine misfires, and the illumination of the check engine light.

2. What does the OBDII code P013D indicate in a Buick?

- The code indicates a slow response from the HO2S (Heated Oxygen Sensor) from lean to rich on Bank 2 Sensor 2, signaling a potential issue with the sensor's performance.

3. What are the possible causes of OBDII code P013D in a Buick?

- Potential causes include a faulty HO2S (Bank 2 Sensor 2), wiring or connector issues, exhaust leaks, vacuum leaks, or a problem with the engine's air-fuel mixture.

4. How can I diagnose the OBDII code P013D in my Buick?

- Diagnosis typically involves using a scan tool to read the code, inspecting the HO2S (Bank 2 Sensor 2) and its wiring, checking for exhaust or vacuum leaks, and verifying the air-fuel mixture.

5. How can I repair OBDII code P013D in my Buick?

- Repair options may include replacing the HO2S (Bank 2 Sensor 2), repairing or replacing damaged wiring or connectors, fixing any exhaust or vacuum leaks, and ensuring the proper functioning of the air-fuel mixture.

6. Can I drive my Buick with OBDII code P013D?

- It's not recommended to drive with this code unaddressed, as it can lead to reduced fuel efficiency, engine performance issues, and potential damage to the catalytic converter over time.

7. How much does it cost to repair OBDII code P013D in a Buick?

- The cost of repairs can vary based on the specific issue causing the code, but it may range from a few hundred to a few thousand dollars, depending on the extent of the problem and whether professional help is needed.

8. Are there any preventative measures to avoid OBDII code P013D in a Buick?

- Regular vehicle maintenance, such as checking and replacing oxygen sensors as recommended, addressing any engine performance issues promptly, and ensuring proper fuel and air intake, can help prevent this code from occurring.

9. How urgent is it to address OBDII code P013D in a Buick?

- While the vehicle may still be operable with this code, it's important to address it promptly to prevent potential damage to the engine or emissions system and to maintain optimal fuel efficiency and performance.

10. Can I reset the check engine light after repairing OBDII code P013D in my Buick?

- Yes, once the underlying issue causing the code has been resolved, the check engine light can be reset using a scan tool to clear the stored code and turn off the light.