P0135 BMW Code - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1
Quick Answer
Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit fuse, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit open shorted to ground. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P0135 BMW indicates O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1.
- Common causes
- Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit fuse, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit open shorted to ground.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P0135 BMW Description
In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECM controls the heater element circuit by allowing current flow to ground.
The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.
What are the Possible Causes of the DTC P0135 BMW?
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit fuse
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 1 circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0135 BMW?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0135 BMW code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0135 BMW code?
Need more information on how to fix the P0135 BMW code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0135 BMW code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0135 BMW Code
1. What are the common symptoms of OBDII code P0135 in a BMW?
- Common symptoms include poor fuel economy, rough idling, engine misfires, and the illumination of the Check Engine light.
2. What does the O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1 mean in a BMW?
- This code indicates that there is an issue with the heating element circuit of the oxygen sensor located in the exhaust system before the catalytic converter on bank 1.
3. What are some possible causes of the P0135 OBDII code in a BMW?
- Possible causes include a faulty oxygen sensor, damaged wiring or connectors in the sensor circuit, a blown fuse, or a problem with the engine control module (ECM).
4. How can I diagnose the O2 Sensor Heater Circuit Malfunction in my BMW?
- Diagnosing this issue typically involves checking the oxygen sensor's wiring and connectors for damage, testing the sensor's resistance, and inspecting the fuse related to the sensor circuit.
5. Can I drive my BMW with the P0135 error code?
- While it may be possible to drive the vehicle with this code, it is not recommended as it can lead to reduced fuel efficiency and potential damage to the catalytic converter over time.
6. How can I repair the O2 Sensor Heater Circuit Malfunction in my BMW?
- Repairing this issue often involves replacing the faulty oxygen sensor, repairing damaged wiring or connectors, and resetting the error code using an OBDII scanner.
7. Are there any tips to prevent the P0135 code from recurring in my BMW?
- To prevent this code from reoccurring, ensure proper maintenance of the oxygen sensors, avoid driving with a misfiring engine, and regularly check the integrity of the sensor's wiring and connectors.
8. Can a DIY enthusiast fix the P0135 code in a BMW?
- Depending on your level of automotive knowledge and experience, it may be possible to fix this issue yourself by following repair guides and using the necessary tools and equipment.
9. How much does it typically cost to repair the P0135 code in a BMW?
- The cost of repairs for this code can vary depending on the underlying issue, but it generally ranges from $100 to $300 for parts and labor if a professional mechanic handles the repair.
10. Is it safe to ignore the P0135 code in a BMW?
- Ignoring this code can lead to decreased fuel efficiency, potential engine damage, and emission regulation issues, so it is recommended to address the problem promptly.
Discuss the causes and fixes for P0135 BMW OBDII Code
Code P0135 BMW comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
