AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Chevrolet - P0133 2018 Chevrolet Silverado

P0133 2018 Chevrolet Silverado Code - HO2S Slow Response Bank 1 Sensor 1

- Code Popularity: 187 Views
- Repair Importance Level: 2/3
- Repair Difficulty Level: 2/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC P0133 2018 Chevrolet Silverado?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Heated Oxygen Sensor (HO2S) Bank 1 Sensor 1
  • Heated Oxygen Sensor Bank 1 Sensor 1 harness is open or shorted
  • Heated Oxygen Sensor Bank 1 Sensor 1 circuit poor electrical connection
  • Low or high fuel system pressure
  • Fuel contamination
  • Faulty fuel injectors
  • Exhaust gas leaks
  • Engine vacuum leaks
⚠ Does your Chevrolet have Safety Recalls? → Check here

How to Fix the DTC P0133 2018 Chevrolet Silverado?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Code Tech Notes

Replacing the Front Heated Oxygen Sensors (HO2S) usually takes care of the problem

Search for P0133 2018 Chevrolet Silverado Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0133 2018 Chevrolet Silverado code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)
  • High Fuel Consumption
  • Excessive Smoke from Exhaust

Code P0133 2018 Chevrolet Silverado Description

The Heated Oxygen Sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content of the exhaust stream. When the engine is started, the Engine Control Module (ECM) operates in an Open Loop mode, ignoring the HO2S signal voltage while calculating the air-to-fuel ratio. While the engine runs, the HO2S heats up and begins to generate a voltage within a range of 0 - 1, 000 mV. Once sufficient HO2S voltage fluctuation is observed by the ECM, Closed Loop is entered. The ECM uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1, 000 mV indicates a rich fuel mixture. An HO2S voltage that decreases toward 0 mV indicates a lean fuel mixture.
The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed Loop earlier and the ECM to calculate the air-to-fuel ratio sooner.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects that the HO2S 1 rich-to-lean or lean-to-rich average response time is greater than a calibrated value for greater than 60s.
OBDII Code P0133 2018 Chevrolet Silverado - HO2S Slow Response Bank 1 Sensor 1 - AutoCodes.com
P0133 2018 Chevrolet Silverado Code - HO2S Slow Response Bank 1 Sensor 1

Need More Information on the Code?

Need more information on how to fix the P0133 2018 Chevrolet Silverado code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0133 2018 Chevrolet Silverado code diagnosed by a professional: Find a repair shop in your area

Code P0133 2018 Chevrolet Silverado comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P0133 2018 Chevrolet Silverado code? Have you replaced any parts?
Any information is appreciated. Thanks