AutoCodes – Generic – P010A

P010A Code - Mass Or Volume Air Flow Sensor 'B' Circuit

Quick Answer

The Mass Airflow (MAF) Sensor uses a hot wire sensing element to measure the amount of air entering the engine. Common causes include Dirty Air Filter, Faulty Mass Airflow Bank 2 Sensor 1 (MAF21), Mass Airflow Bank 2 Sensor 1 harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P010A indicates Mass Or Volume Air Flow Sensor 'B' Circuit.
Common causes: Common causes include Dirty Air Filter, Faulty Mass Airflow Bank 2 Sensor 1 (MAF21), Mass Airflow Bank 2 Sensor 1 harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 14,338

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Sep 21, 2023

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P010A Description

The Mass Airflow (MAF) Sensor uses a hot wire sensing element to measure the amount of air entering the engine. The air passing over the hot wire causes it to cool. This hot wire is maintained at 200°C (392°F) above the ambient temperature as measured by a constant cold wire. The current required to maintain the temperature of the hot wire is proportional to the mass airflow. The MAF Sensor then outputs a signal to the Powertrain Control Module (PCM) proportional to the intake air mass. The PCM calculates the required fuel injector pulse width in order to provide the desired air to fuel ratio. The MAF sensor is located near the air cleaner assembly. Most MAF sensors have an integrated Intake Air Temperature (IAT) sensor. This Diagnostic Trouble Code (DTC) will be set when the Mass Airflow Bank 2, Sensor 1 (MAF21) frequency changes below a minimum calibrated limit for greater than 0.5 seconds.

OBDII Code P010A - Mass Or Volume Air Flow Sensor 'B' Circuit - AutoCodes.com — P010A Code - Mass Or Volume Air Flow Sensor 'B' Circuit

What does this mean?

What are the Possible Causes of the DTC P010A?

Dirty Air Filter
Faulty Mass Airflow Bank 2 Sensor 1 (MAF21)
Mass Airflow Bank 2 Sensor 1 harness is open or shorted
Mass Airflow Bank 2 Sensor 1 circuit poor electrical connection

How to Fix the DTC P010A?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

Before replacing the Mass Air Flow (MAF) Sensor, try replacing the air filter and cleaning the Mass Air Flow Sensor with low-compressed air or a Mass Air Flow Sensor Cleaner. Reset the code and drive the vehicle. If the code comes back, you must replace the Mass Air Flow Sensor to fix the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P010A code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P010A code?

Need more information on how to fix the P010A code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P010A code diagnosed by a professional: Find a repair shop in your area

Information for Specific Makes

P010A Ford — Mass Or Volume Air Flow Sensor 'B' Circuit
P010A Lincoln — Mass Or Volume Air Flow Sensor 'B' Circuit

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.