P0107 1998 Honda Civic Code - Manifold Absolute Pressure Sensor Circuit Low Voltage
Quick Answer
The Manifold Absolute Pressure (MAP) sensor measures the pressure inside the intake manifold. Common causes include Faulty Manifold Absolute Pressure (MAP) Sensor, Manifold Absolute Pressure Sensor harness is open or shorted, Manifold Absolute Pressure Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0107 1998 Honda Civic indicates Manifold Absolute Pressure Sensor Circuit Low Voltage.
- Common causes
- Common causes include Faulty Manifold Absolute Pressure (MAP) Sensor, Manifold Absolute Pressure Sensor harness is open or shorted, Manifold Absolute Pressure Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0107 1998 Honda Civic Description
The MAP sensor wiring includes 3 circuits. The Engine Control Module (ECM) supplies a regulated 5 volts to the sensor on a 5 V reference circuit. The ECM supplies ground on a low reference circuit. The MAP sensor provides a signal voltage to the ECM, relative to the pressure changes, on the MAP sensor signal circuit. The ECM converts the signal voltage input to a pressure value.
Under normal operation the greatest pressure that can exist in the intake manifold is at ignition ON, engine OFF, which is equal to the BARO. The lowest manifold pressure occurs when the vehicle is idling or decelerating. The ECM monitors the MAP sensor signal for pressure outside of the normal range.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects that the MAP Sensor voltage is less than 0.15 V for greater than 13 ms.
What are the Possible Causes of the DTC P0107 1998 Honda Civic?
- Faulty Manifold Absolute Pressure (MAP) Sensor
- Manifold Absolute Pressure Sensor harness is open or shorted
- Manifold Absolute Pressure Sensor circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0107 1998 Honda Civic?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0107 1998 Honda Civic code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0107 1998 Honda Civic code?
Need more information on how to fix the P0107 1998 Honda Civic code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0107 1998 Honda Civic code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0107 1998 Honda Civic Code
1. What are the common symptoms of OBDII code P0107 in a 1998 Honda Civic?
- Common symptoms include poor engine performance, reduced fuel efficiency, rough idle, and stalling.
2. What can cause the Manifold Absolute Pressure (MAP) sensor circuit to show low voltage in a 1998 Honda Civic?
- Possible causes include a faulty MAP sensor, damaged wiring or connectors, a vacuum leak, or a problem with the engine's intake system.
3. How can I diagnose the issue causing OBDII code P0107 in my 1998 Honda Civic?
- You can use a multimeter to test the voltage output of the MAP sensor, visually inspect the wiring and connectors for damage, and check for any vacuum leaks.
4. Can a dirty or clogged MAP sensor cause OBDII code P0107 in a 1998 Honda Civic?
- Yes, a dirty or clogged MAP sensor can disrupt the sensor's readings and potentially lead to low voltage issues triggering the P0107 code.
5. Is it safe to continue driving my 1998 Honda Civic with OBDII code P0107 present?
- It is not recommended to continue driving with this code as it can lead to further engine damage and potential safety issues due to poor performance.
6. How can I reset the OBDII code P0107 in my 1998 Honda Civic?
- You can reset the code using an OBDII scanner or by disconnecting the car's battery for a few minutes to clear the error code.
7. What are some repair tips for fixing OBDII code P0107 in a 1998 Honda Civic?
- Repair tips include checking and replacing the MAP sensor if necessary, repairing any damaged wiring or connectors, and ensuring there are no vacuum leaks in the intake system.
8. Can a DIY enthusiast fix OBDII code P0107 in a 1998 Honda Civic?
- Depending on your automotive knowledge and skills, you may be able to diagnose and fix the issue causing the P0107 code, such as replacing the MAP sensor or fixing wiring problems.
9. Will fixing OBDII code P0107 improve the overall performance of my 1998 Honda Civic?
- Yes, resolving the low voltage issue related to the MAP sensor can improve engine performance, fuel efficiency, and overall drivability of your Honda Civic.
10. How much does it typically cost to repair OBDII code P0107 in a 1998 Honda Civic at a professional mechanic?
- The cost of repairing the P0107 code can vary depending on the specific cause of the issue, but it may range from $100 to $300 for parts and labor at a professional mechanic's shop.
Discuss the causes and fixes for P0107 1998 Honda Civic OBDII Code
Code P0107 1998 Honda Civic comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
