AutoCodes – Ford – P0106 2007 Ford Fusion

P0106 2007 Ford Fusion Code - Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance

Quick Answer

The Manifold Absolute Pressure (MAP) sensor measures the pressure inside the intake manifold. Common causes include Faulty Manifold Absolute Pressure (MAP) Sensor, Manifold Absolute Pressure Sensor harness is open or shorted, Manifold Absolute Pressure Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P0106 2007 Ford Fusion indicates Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance.
Common causes: Common causes include Faulty Manifold Absolute Pressure (MAP) Sensor, Manifold Absolute Pressure Sensor harness is open or shorted, Manifold Absolute Pressure Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs Step-by-Step Diagnostic Guide My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 5,850

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 19, 2022

Description
Step-by-Step Diagnostic Guide
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0106 2007 Ford Fusion Description

The Manifold Absolute Pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the intake manifold is affected by engine speed, throttle opening, air temperature, Barometric Pressure (BARO) and if equipped, turbocharger output. A diaphragm within the MAP sensor is displaced by the pressure changes that occur from the varying load and operating conditions of the engine. The sensor translates this action into electrical resistance.
The MAP sensor wiring includes 3 circuits. The Engine Control Module (ECM) supplies a regulated 5 volts to the sensor on a 5 V reference circuit. The ECM supplies ground on a low reference circuit. The MAP sensor provides a signal voltage to the ECM, relative to the pressure changes, on the MAP sensor signal circuit. The ECM converts the signal voltage input to a pressure value.
Under normal operation the greatest pressure that can exist in the intake manifold is at ignition ON, engine OFF, which is equal to the BARO. The lowest manifold pressure occurs when the vehicle is idling or decelerating. The ECM monitors the MAP sensor signal for pressure outside of the normal range.
The Diagnostic Trouble Code (DTC) will be set when the ECM determines the MAP Sensor is stuck within the normal operating range. It accomplishes this by running 3 different models within the software to determine the values.

OBDII Code P0106 2007 Ford Fusion - Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance - AutoCodes.com — P0106 2007 Ford Fusion Code - Manifold Absolute Pressure/Barometric Pressure Sensor Range/Performance

What does this mean?

What are the Possible Causes of the DTC P0106 2007 Ford Fusion?

Faulty Manifold Absolute Pressure (MAP) Sensor
Manifold Absolute Pressure Sensor harness is open or shorted
Manifold Absolute Pressure Sensor circuit poor electrical connection
Faulty Engine Control Module (ECM)

How to Fix the DTC P0106 2007 Ford Fusion?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

You can try to clean the MAP (Manifold Absolute Pressure) sensor with mass air flow sensor cleaner.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0106 2007 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0106 2007 Ford Fusion code?

Need more information on how to fix the P0106 2007 Ford Fusion code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0106 2007 Ford Fusion code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0106 2007 Ford Fusion Code

1. What does OBDII code P0106 for a 2007 Ford Fusion indicate?

The P0106 code specifically refers to an issue with the Manifold Absolute Pressure (MAP) or Barometric Pressure (BARO) sensor range/performance.

2. What are the common symptoms of a P0106 code in a 2007 Ford Fusion?

Common symptoms include rough idling, decreased engine performance, poor fuel efficiency, stalling, and in some cases, the vehicle may not start.

3. What are the possible causes of a P0106 code in a 2007 Ford Fusion?

Possible causes include a faulty MAP/BARO sensor, damaged wiring or connectors, intake manifold leaks, vacuum system leaks, or issues with the engine control module (ECM).

4. How can I diagnose a P0106 code in my 2007 Ford Fusion?

Diagnosing a P0106 code typically involves checking the sensor's wiring and connections, inspecting the intake manifold and vacuum system for leaks, and testing the sensor's voltage output using a multimeter.

5. Can I drive my 2007 Ford Fusion with a P0106 code?

Continuing to drive with a P0106 code can potentially cause further damage to the engine and negatively impact performance and fuel efficiency. It's recommended to address the issue promptly.

6. How do I repair a P0106 code in my 2007 Ford Fusion?

Repairing a P0106 code may involve replacing the faulty MAP/BARO sensor, repairing any damaged wiring or connectors, fixing any leaks in the intake manifold or vacuum system, or reprogramming the ECM if necessary.

7. Is it possible to reset a P0106 code in a 2007 Ford Fusion without fixing the underlying issue?

Resetting the code without addressing the root cause will only temporarily clear the error code. The issue will likely resurface, and it's important to diagnose and repair the problem to prevent further issues.

8. Can a dirty air filter cause a P0106 code in a 2007 Ford Fusion?

A dirty air filter can restrict airflow to the engine, potentially affecting sensor readings and leading to a P0106 code. It's recommended to check and replace a dirty air filter as part of troubleshooting.

9. How long does it typically take to repair a P0106 code in a 2007 Ford Fusion?

The repair time for a P0106 code can vary depending on the exact cause of the issue. Simple fixes like replacing a sensor or repairing a connection may take an hour or two, while more complex issues could require more time.

10. Will a P0106 code in a 2007 Ford Fusion cause the check engine light to illuminate?

Yes, a P0106 code will trigger the check engine light to illuminate on the dashboard of the 2007 Ford Fusion. It's important not to ignore this warning and to address the underlying issue promptly.