AutoCodes – Jeep – P0103 Jeep

P0103 Jeep Code - Mass Air Flow Sensor Circuit Low

Quick Answer

The Mass Air Flow (MAF) sensor is placed in the stream of the intake air. Common causes include Dirty Air Filter, Dirty Mass Air Flow (MAF) Sensor, Intake air leaks. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P0103 Jeep indicates Mass Air Flow Sensor Circuit Low.
Common causes: Common causes include Dirty Air Filter, Dirty Mass Air Flow (MAF) Sensor, Intake air leaks.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs Step-by-Step Diagnostic Guide My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 12,967

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 19, 2022

Description
Step-by-Step Diagnostic Guide
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0103 Jeep Description

The Mass Air Flow (MAF) sensor is placed in the stream of the intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module (ECM). The ECM controls the temperature of the hot film by a certain amount. The heat generated by the hot film is reduced as the intake air flows around it. The more air, the greater the heat loss. Therefore, the ECM must supply more electric current to maintain the temperature of the hot film as air flow increases. The ECM detects the air flow by means of this current change. The Diagnostic Trouble Code (DTC) will be set when the ECM detects that the MAF Sensor Signal is more than the factory specifications.

OBDII Code P0103 Jeep - Mass Air Flow Sensor Circuit Low - AutoCodes.com — P0103 Jeep Code - Mass Air Flow Sensor Circuit Low

What does this mean?

What are the Possible Causes of the DTC P0103 Jeep?

Dirty Air Filter
Dirty Mass Air Flow (MAF) Sensor
Intake air leaks
Faulty Mass Air Flow Sensor
Mass Air Flow Sensor harness is open or shorted
Mass Air Flow Sensor circuit poor electrical connection

How to Fix the DTC P0103 Jeep?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

Before replacing the Mass Air Flow (MAF) Sensor, try replacing the air filter and cleaning the Mass Air Flow Sensor with low compress air or Mass Air Flow Sensor Cleaner. Reset code and drive vehicle. If the code comes back, you must replace the Mass Air Flow Sensor to fix the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0103 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0103 Jeep code?

Need more information on how to fix the P0103 Jeep code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0103 Jeep code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.