P0056 Subaru Code - HO2S 22 Heater Control Circuit
Quick Answer
Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2, Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 harness is open shorted, Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P0056 Subaru indicates HO2S 22 Heater Control Circuit.
- Common causes
- Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2, Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 harness is open shorted, Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 circuit poor electrical connection.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P0056 Subaru Description
In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECM controls the heater element circuit by allowing current flow to ground.
The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.
What are the Possible Causes of the DTC P0056 Subaru?
- Faulty Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2
- Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 harness is open shorted
- Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 circuit poor electrical connection
- Heated Oxygen Sensor (H2OS) Bank 2 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0056 Subaru?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0056 Subaru code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0056 Subaru code?
Need more information on how to fix the P0056 Subaru code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0056 Subaru code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0056 Subaru Code
1. What is OBDII code P0056 on a Subaru?
- OBDII code P0056 for Subaru refers to a malfunction in the HO2S (Heated Oxygen Sensor) 2, Bank 2's heater control circuit.
2. What are common symptoms of OBDII code P0056 in a Subaru?
- Common symptoms of code P0056 in a Subaru may include poor fuel economy, rough idling, engine misfires, and the illumination of the check engine light.
3. What are the potential causes of OBDII code P0056 in a Subaru?
- The potential causes of code P0056 in a Subaru may include a faulty HO2S, damaged wiring or connectors in the heater circuit, a blown fuse, or a problem with the engine control module (ECM).
4. How can I diagnose OBDII code P0056 on my Subaru?
- To diagnose code P0056 on your Subaru, you can use an OBDII scanner to read the code and then inspect the HO2S 2 Bank 2 for any visible damage or issues with the wiring and connectors.
5. Can I still drive my Subaru with OBDII code P0056?
- It is generally not recommended to drive your Subaru with OBDII code P0056, as it can lead to poor engine performance and potentially cause further damage if left unresolved.
6. How do I repair OBDII code P0056 in my Subaru?
- Repairing code P0056 in your Subaru may involve replacing the faulty HO2S, repairing damaged wiring or connectors, checking and replacing any blown fuses, and resetting the ECM.
7. Is it possible to prevent OBDII code P0056 from occurring in my Subaru?
- While some causes of code P0056 may be unavoidable, regular maintenance and timely replacement of oxygen sensors can help prevent this issue from occurring in your Subaru.
8. How much does it typically cost to repair OBDII code P0056 in a Subaru?
- The cost to repair OBDII code P0056 in a Subaru can vary depending on the specific cause of the issue, but it may range from $100 to $300 for parts and labor.
9. Can I reset OBDII code P0056 in my Subaru without fixing the underlying issue?
- While you can clear the code with an OBDII scanner, it is not recommended to reset code P0056 without addressing the root cause, as the issue may persist and lead to further problems.
10. How long does it take to repair OBDII code P0056 in a Subaru?
- The time it takes to repair code P0056 in a Subaru can vary based on the exact cause of the problem and the complexity of the repair, but it typically takes around 1-2 hours for a professional technician to diagnose and fix the issue.
Discuss the causes and fixes for P0056 Subaru OBDII Code
Code P0056 Subaru comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
