AutoCodes – GMC – P0054 2018 GMC Sierra

P0054 2018 GMC Sierra Code - HO2S Heater Resistance Bank 1 Sensor 2

Quick Answer

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P0054 2018 GMC Sierra indicates HO2S Heater Resistance Bank 1 Sensor 2.
Common causes: Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 304

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 25, 2024

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0054 2018 GMC Sierra Description

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach an operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensors to reach operating temperature. Voltage is provided to the heater by an ignition voltage circuit through a fuse. With the engine running, the ground is provided to the heater by the HO2S heater low control circuit through a low side driver within the Engine Control Module (ECM). The ECM uses Pulse Width Modulation (PWM) to control the HO2S heater operation to maintain a specific HO2S operating temperature range.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects the HO2S heater is not within a specified resistance range at engine start-up.

OBDII Code P0054 2018 GMC Sierra - HO2S Heater Resistance Bank 1 Sensor 2 - AutoCodes.com — P0054 2018 GMC Sierra Code - HO2S Heater Resistance Bank 1 Sensor 2

What does this mean?

What are the Possible Causes of the DTC P0054 2018 GMC Sierra?

Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted
Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection
Heated Oxygen Sensor Bank 1 Sensor 2 fuse
Faulty Engine Control Module (ECM)

How to Fix the DTC P0054 2018 GMC Sierra?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The code means that there is a problem with the heater element circuit of the heated oxygen sensor. The control module monitors how long it takes the sensor to warm up and start sending an adequate signal. The code is set when the sensor is taking too long to warm up. Water getting inside the heated oxygen sensor connector can cause the heated oxygen sensor fuse to blow. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors. If the fuse and connector are OK, replacing the O2 Sensor usually takes care of the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0054 2018 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0054 2018 GMC Sierra code?

Need more information on how to fix the P0054 2018 GMC Sierra code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0054 2018 GMC Sierra code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0054 2018 GMC Sierra Code

1. What does OBDII code P0054 on a 2018 GMC Sierra indicate?

The code P0054 for a 2018 GMC Sierra specifically refers to a fault in the HO2S (Heated Oxygen Sensor) heater resistance for Bank 1 Sensor 2.

2. What are the common symptoms of OBDII code P0054 in a GMC Sierra?

Common symptoms of code P0054 in a GMC Sierra may include poor fuel economy, rough idling, engine misfires, and an illuminated Check Engine light.

3. What are the possible causes of OBDII code P0054 in a 2018 GMC Sierra?

Common causes of code P0054 in a 2018 GMC Sierra include a faulty oxygen sensor, damaged wiring or connectors, a blown fuse, or issues with the vehicle's PCM (Powertrain Control Module).

4. How can I diagnose the OBDII code P0054 on my 2018 GMC Sierra?

To diagnose code P0054, you may need to use an OBDII scanner to retrieve the specific fault code. Additionally, inspecting the oxygen sensor, wiring, and related components for damage or corrosion can help pinpoint the issue.

5. Can I drive my 2018 GMC Sierra with OBDII code P0054?

It is generally not recommended to drive your GMC Sierra with an active P0054 code, as it can lead to poor engine performance and potential damage over time. It's best to address the issue promptly.

6. How can I repair OBDII code P0054 on my 2018 GMC Sierra?

Repairing code P0054 may involve replacing the Bank 1 Sensor 2 oxygen sensor, checking and repairing any damaged wiring or connectors, ensuring the fuse is intact, and resetting the fault code with an OBDII scanner.

7. Is it necessary to reset the Check Engine light after repairing OBDII code P0054?

Yes, it is recommended to reset the Check Engine light using an OBDII scanner after repairing code P0054 on your 2018 GMC Sierra. This ensures the system recognizes that the issue has been resolved.

8. How much does it cost to repair OBDII code P0054 on a 2018 GMC Sierra?

The cost of repairing code P0054 on a 2018 GMC Sierra can vary depending on the specific underlying issue, labor rates, and whether you choose to address the problem yourself or take it to a mechanic. Costs may include parts and labor.

9. Can a DIY enthusiast repair OBDII code P0054 on a 2018 GMC Sierra?

Yes, a DIY enthusiast with the necessary tools and knowledge can potentially repair code P0054 on a 2018 GMC Sierra. However, it's important to be comfortable working with automotive electrical systems and diagnostics.

10. How can I prevent OBDII code P0054 from recurring on my 2018 GMC Sierra?

To prevent code P0054 from recurring, it's important to address any underlying issues promptly, perform regular maintenance on your vehicle's oxygen sensors and related components, and avoid driving with a misfiring engine.