P0044 Mitsubishi Code - HO2S Heater Control Circuit High Bank 1 Sensor 3
Quick Answer
Oxygen Sensors (O2S) or Heated Oxygen Sensors (HO2S) need to reach a minimum operating temperature of 750 degrees F to produce an accurate voltage signal. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 harness is open shorted, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P0044 Mitsubishi indicates HO2S Heater Control Circuit High Bank 1 Sensor 3.
- Common causes
- Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 harness is open shorted, Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit poor electrical connection.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P0044 Mitsubishi Description
In order to achieve the require temperature, a heater element is included inside the heated oxygen sensor. The ECM controls the heated oxygen sensor heater element based on signals from the engine coolant temperature and engine load. The ECM controls the heater element circuit by allowing current flow to ground.
The ECM monitors the voltage signal received through the heater element circuit and determines the state of the circuit by comparing the voltage detected with the factory specifications.
What are the Possible Causes of the DTC P0044 Mitsubishi?
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 harness is open shorted
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 circuit poor electrical connection
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 3 fuse
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0044 Mitsubishi?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0044 Mitsubishi code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0044 Mitsubishi code?
Need more information on how to fix the P0044 Mitsubishi code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0044 Mitsubishi code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0044 Mitsubishi Code
1. What does the OBDII code P0044 mean for a Mitsubishi vehicle?
P0044 indicates a high voltage issue in the heater control circuit for the oxygen sensor (HO2S) on Bank 1, Sensor 3.
2. What are the common symptoms of P0044 in a Mitsubishi?
Symptoms may include an illuminated check engine light, increased fuel consumption, rough idling, or failed emissions tests.
3. What causes the P0044 code to appear?
Possible causes include a faulty oxygen sensor, damaged wiring or connectors, a malfunctioning heater circuit, or a defective engine control module (ECM).
4. Which sensor does P0044 refer to on a Mitsubishi?
P0044 refers to the Bank 1, Sensor 3 oxygen sensor, which is located downstream of the catalytic converter.
5. Can I drive my Mitsubishi with a P0044 code?
While the vehicle may still be drivable, ignoring this code can lead to reduced fuel efficiency, increased emissions, and potential damage to other components.
6. How can I diagnose the P0044 code on a Mitsubishi?
Use an OBDII scanner to confirm the code, visually inspect the wiring and connectors for damage, and test the oxygen sensor heater circuit for proper voltage and resistance.
7. How do I fix the P0044 code on my Mitsubishi?
Repairs may involve replacing the faulty oxygen sensor, repairing damaged wiring or connectors, or addressing issues in the ECM.
8. What tools are needed to troubleshoot the P0044 code?
You’ll need an OBDII scanner, a multimeter to test electrical circuits, and possibly a wiring diagram for your vehicle.
9. How much does it cost to repair a P0044 code on a Mitsubishi?
Repair costs vary but typically range from $100 to $400, depending on whether the oxygen sensor or other components need replacement.
10. Can a faulty ECM cause the P0044 code on a Mitsubishi?
Yes, though rare, a malfunctioning ECM can fail to regulate the heater circuit properly, triggering the P0044 code.
Discuss the causes and fixes for P0044 Mitsubishi OBDII Code
Code P0044 Mitsubishi comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
