AutoCodes – GMC – P0036 2018 GMC Sierra

P0036 2018 GMC Sierra Code - HO2S Heater Control Circuit Bank 1 Sensor 2

Quick Answer

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P0036 2018 GMC Sierra indicates HO2S Heater Control Circuit Bank 1 Sensor 2.
Common causes: Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs Step-by-Step Diagnostic Guide My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 252

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 25, 2024

Description
Step-by-Step Diagnostic Guide
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0036 2018 GMC Sierra Description

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach an operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensors to reach operating temperature. Voltage is provided to the heater by an ignition voltage circuit through a fuse. With the engine running, the ground is provided to the heater by the HO2S heater low control circuit through a low side driver within the Engine Control Module (ECM). The ECM uses Pulse Width Modulation (PWM) to control the HO2S heater operation to maintain a specific HO2S operating temperature range.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects an open circuit in the heater output low side driver circuit of the heated oxygen sensor when the heater is commanded OFF for greater than 5 s.

OBDII Code P0036 2018 GMC Sierra - HO2S Heater Control Circuit Bank 1 Sensor 2 - AutoCodes.com — P0036 2018 GMC Sierra Code - HO2S Heater Control Circuit Bank 1 Sensor 2

What does this mean?

What are the Possible Causes of the DTC P0036 2018 GMC Sierra?

Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground
Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection
Heated Oxygen Sensor Bank 1 Sensor 2 circuit fuse
Faulty Engine Control Module (ECM)

How to Fix the DTC P0036 2018 GMC Sierra?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The code means that there is a problem with the heater element circuit of the heated oxygen sensor. The control module monitors how long it takes the sensor to warm up and start sending an adequate signal. The code is set when the sensor is taking too long to warm up. Water getting inside the heated oxygen sensor connector can cause the heated oxygen sensor fuse to blow. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors. If the fuse and connector are OK, replacing the O2 Sensor usually takes care of the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0036 2018 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0036 2018 GMC Sierra code?

Need more information on how to fix the P0036 2018 GMC Sierra code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0036 2018 GMC Sierra code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0036 2018 GMC Sierra Code

1. What does OBDII code P0036 for a 2018 GMC Sierra mean?

- This code refers to a malfunction in the HO2S (Heated Oxygen Sensor) heater control circuit for Bank 1 Sensor 2.

2. What are common symptoms associated with OBDII code P0036 in a GMC Sierra?

- Common symptoms include poor fuel economy, rough idling, engine misfires, and an illuminated check engine light.

3. What are the possible causes of OBDII code P0036 in a 2018 GMC Sierra?

- The potential causes include a faulty oxygen sensor, damaged wiring or connectors, a blown fuse, or issues with the ECM (Engine Control Module).

4. How can I diagnose the HO2S heater control circuit for Bank 1 Sensor 2 issue in my GMC Sierra?

- Diagnosing this problem typically involves checking the sensor's wiring and connectors, testing the heater circuit resistance, and inspecting the sensor's voltage output.

5. Can I still drive my GMC Sierra with the P0036 code?

- It's generally not recommended to drive the vehicle with this code as it can lead to reduced fuel efficiency and potential damage to the catalytic converter.

6. How can I repair OBDII code P0036 in my 2018 GMC Sierra?

- Repairing this code may involve replacing the oxygen sensor, repairing damaged wiring or connectors, checking and replacing fuses if needed, or reprogramming the ECM.

7. Are there any DIY tips for fixing the HO2S heater control circuit issue in a GMC Sierra?

- DIY enthusiasts may attempt to inspect and replace the oxygen sensor, check and repair wiring connections, and replace blown fuses as potential solutions.

8. Is it essential to address the P0036 code immediately in my GMC Sierra?

- It's advisable to address this code promptly to prevent further engine performance issues and ensure optimal fuel efficiency.

9. Can a mechanic easily fix the OBDII code P0036 in a 2018 GMC Sierra?

- A qualified mechanic can effectively diagnose and repair the HO2S heater control circuit problem in a GMC Sierra using specialized tools and expertise.

10. How much should I expect to pay for repairing the HO2S heater control circuit issue in a GMC Sierra?

- The cost of repairing OBDII code P0036 can vary based on the extent of the issue, parts needed, and labor rates, but it generally ranges from $150 to $400.