AutoCodes – GMC – P0036 2014 GMC Sierra

P0036 2014 GMC Sierra Code - HO2S Heater Control Circuit Bank 1 Sensor 2

Quick Answer

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P0036 2014 GMC Sierra indicates HO2S Heater Control Circuit Bank 1 Sensor 2.
Common causes: Common causes include Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2, Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground, Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs Step-by-Step Diagnostic Guide My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 225

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 25, 2024

Description
Step-by-Step Diagnostic Guide
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P0036 2014 GMC Sierra Description

Heated Oxygen Sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach an operating temperature to provide an accurate voltage signal. A heating element inside the HO2S minimizes the time required for the sensors to reach operating temperature. Voltage is provided to the heater by an ignition voltage circuit through a fuse. With the engine running, the ground is provided to the heater by the HO2S heater low control circuit through a low side driver within the Engine Control Module (ECM). The ECM uses Pulse Width Modulation (PWM) to control the HO2S heater operation to maintain a specific HO2S operating temperature range.
The Diagnostic Trouble Code (DTC) will be set when the ECM detects an open circuit in the heater output low side driver circuit of the heated oxygen sensor when the heater is commanded OFF for greater than 5 s.

OBDII Code P0036 2014 GMC Sierra - HO2S Heater Control Circuit Bank 1 Sensor 2 - AutoCodes.com — P0036 2014 GMC Sierra Code - HO2S Heater Control Circuit Bank 1 Sensor 2

What does this mean?

What are the Possible Causes of the DTC P0036 2014 GMC Sierra?

Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2
Heated Oxygen Sensor Bank 1 Sensor 2 harness is open shorted to ground
Heated Oxygen Sensor Bank 1 Sensor 2 circuit poor electrical connection
Heated Oxygen Sensor Bank 1 Sensor 2 circuit fuse
Faulty Engine Control Module (ECM)

How to Fix the DTC P0036 2014 GMC Sierra?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The code means that there is a problem with the heater element circuit of the heated oxygen sensor. The control module monitors how long it takes the sensor to warm up and start sending an adequate signal. The code is set when the sensor is taking too long to warm up. Water getting inside the heated oxygen sensor connector can cause the heated oxygen sensor fuse to blow. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors. If the fuse and connector are OK, replacing the O2 Sensor usually takes care of the problem.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P0036 2014 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P0036 2014 GMC Sierra code?

Need more information on how to fix the P0036 2014 GMC Sierra code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0036 2014 GMC Sierra code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0036 2014 GMC Sierra Code

1. What are the common symptoms of OBDII code P0036 on a 2014 GMC Sierra?

- Common symptoms include the Check Engine Light being illuminated, poor fuel economy, rough idling, and potential issues with the vehicle's emissions.

2. What does the OBDII code P0036 for a 2014 GMC Sierra indicate?

- OBDII code P0036 indicates a problem with the HO2S (Heated Oxygen Sensor) Heater Control Circuit for Bank 1 Sensor 2 in the vehicle's exhaust system.

3. What are the possible causes of OBDII code P0036 on a 2014 GMC Sierra?

- Possible causes include a faulty oxygen sensor, damaged wiring or connectors related to the sensor, a blown fuse, or issues with the sensor's heating element.

4. How can I diagnose the OBDII code P0036 on my 2014 GMC Sierra?

- Diagnosing OBDII code P0036 typically involves using an OBDII scanner to retrieve the code, inspecting the sensor and its wiring for any visible damage, and testing the sensor's heating element for proper functioning.

5. Can I still drive my 2014 GMC Sierra with OBDII code P0036 present?

- While it may be possible to drive the vehicle with the code present, it is recommended to address the issue promptly to prevent potential damage to the vehicle's catalytic converter and ensure optimal performance.

6. How can I repair OBDII code P0036 on a 2014 GMC Sierra?

- Repairing OBDII code P0036 may involve replacing the faulty oxygen sensor, repairing damaged wiring or connectors, checking and replacing any blown fuses, and clearing the trouble code with an OBDII scanner.

7. Is it safe to continue driving my 2014 GMC Sierra if the Check Engine Light is on due to OBDII code P0036?

- It's generally safe to drive the vehicle for a short period with the Check Engine Light on, but it's advisable to have the issue diagnosed and repaired as soon as possible to avoid potential further damage.

8. How much does it typically cost to fix OBDII code P0036 on a 2014 GMC Sierra?

- The cost of fixing OBDII code P0036 can vary depending on the specific cause of the issue, but it may range from $100 to $300 for parts and labor if replacing the oxygen sensor or repairing the wiring.

9. Can a DIY enthusiast repair OBDII code P0036 on a 2014 GMC Sierra?

- While some DIY enthusiasts may have the skills to address OBDII code P0036 by replacing the oxygen sensor or checking the wiring, it's essential to have the necessary tools and knowledge to ensure a successful repair.

10. How often does OBDII code P0036 occur in a 2014 GMC Sierra?

- OBDII code P0036 can occur sporadically in a 2014 GMC Sierra due to various factors like sensor wear, electrical issues, or environmental conditions, but prompt diagnosis and repair are key to resolving the problem efficiently.