U3003 Mercury Code - ABS Module Battery Voltage
Quick Answer
The Anti-Lock Brake System (ABS) Module, hydraulic pump and solenoid valves require an operating voltage that is between 10 and 17 volts. Common causes include Faulty Anti-Lock Brake System (ABS) Module, Anti-Lock Brake System (ABS) Module harness is open or shorted, Anti-Lock Brake System (ABS) Module circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- U3003 Mercury indicates ABS Module Battery Voltage.
- Common causes
- Common causes include Faulty Anti-Lock Brake System (ABS) Module, Anti-Lock Brake System (ABS) Module harness is open or shorted, Anti-Lock Brake System (ABS) Module circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code U3003 Mercury Description
Internally to the ABS module, the ignition voltage supply circuit is used as a redundant back up for the battery voltage supply circuit in case the battery voltage supply circuit is interrupted. If the battery voltage supply circuit is interrupted, the ABS module immediately shuts off and does not enter the power latch mode. The module uses the power latch mode to write certain parameters (such as learned offsets numbers) to non-volatile memory. At the beginning of each ignition cycle, a counter value is increased by 1 after a specified vehicle speed has been reached and a specified time has elapsed. When the ABS module enters the power latch mode, this counter is reset to 0.
What are the Possible Causes of the DTC U3003 Mercury?
- Faulty Anti-Lock Brake System (ABS) Module
- Anti-Lock Brake System (ABS) Module harness is open or shorted
- Anti-Lock Brake System (ABS) Module circuit poor electrical connection
How to Fix the DTC U3003 Mercury?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the U3003 Mercury code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the U3003 Mercury code?
Need more information on how to fix the U3003 Mercury code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the U3003 Mercury code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about U3003 Mercury Code
1. What is OBDII code U3003 for a Mercury related to the ABS Module Battery Voltage?
The U3003 code specifically indicates a low voltage condition in the ABS module's battery power supply.
2. What are some common symptoms of OBDII code U3003 in a Mercury?
Common symptoms include the ABS warning light illuminating on the dashboard, potential loss of ABS functionality, and intermittent issues with braking performance.
3. What are the possible causes of OBDII code U3003 in a Mercury?
Potential causes of the U3003 code include a weak or failing ABS module battery, corroded electrical connections, a faulty ABS module, or issues with the vehicle's main battery or charging system.
4. How can I diagnose the OBDII code U3003 in my Mercury?
Diagnosing the U3003 code typically involves using a diagnostic scanner to retrieve the code, checking the vehicle's battery voltage and connections, inspecting the ABS module for any visible damage, and testing the ABS system for proper function.
5. Can I still drive my Mercury with the OBDII code U3003 present?
It is not recommended to drive your Mercury with the U3003 code present, as it indicates a potential issue with the ABS system that could compromise your vehicle's braking performance and safety.
6. How can I fix OBDII code U3003 in my Mercury?
To fix the U3003 code, you may need to replace the ABS module battery, clean or repair any corroded connections, or address any underlying issues with the vehicle's main battery or charging system. It is advisable to seek professional help for accurate diagnosis and repair.
7. Will resetting the OBDII code U3003 in my Mercury make the problem go away?
Resetting the code may temporarily turn off the warning light, but it will not fix the underlying issue causing the U3003 code. It is important to diagnose and address the root cause of the problem to prevent safety risks.
8. Are there any safety concerns associated with OBDII code U3003 in a Mercury?
Yes, the U3003 code related to the ABS Module Battery Voltage can impact the functionality of your vehicle's ABS system, potentially affecting your ability to brake safely in certain driving conditions. Prompt attention and repair are recommended.
9. How much does it typically cost to repair OBDII code U3003 in a Mercury?
The cost of repairing the U3003 code can vary depending on the underlying cause and the specific repairs needed. It is advisable to consult a professional mechanic for an accurate diagnosis and cost estimate.
10. Can I prevent OBDII code U3003 from recurring in my Mercury?
Regular maintenance of your vehicle's electrical system, including the ABS module battery and connections, can help prevent the recurrence of the U3003 code. Promptly addressing any warning lights or unusual symptoms can also help prevent further issues.
Discuss the causes and fixes for U3003 Mercury OBDII Code
Code U3003 Mercury comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
