P3044 Buick Code - Hybrid/EV Battery Interface Control Module 12 Voltage Sensor Circuit High Voltage
Quick Answer
The hybrid battery contains 192 individual cells. Common causes include Faulty Hybrid/EV Battery Interface Control Module, Hybrid/EV Battery Interface Control Module harness is open or shorted, Hybrid/EV Battery Interface Control Module circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P3044 Buick indicates Hybrid/EV Battery Interface Control Module 12 Voltage Sensor Circuit High Voltage.
- Common causes
- Common causes include Faulty Hybrid/EV Battery Interface Control Module, Hybrid/EV Battery Interface Control Module harness is open or shorted, Hybrid/EV Battery Interface Control Module circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P3044 Buick Description
The battery energy control module monitors the voltage of the 96 battery cell groups. The voltage sense lines are attached to each individual cell group, and these sense lines terminate at a connector located on the top surface of the battery section. A voltage sense harness joins this connector to the battery energy control module.
The battery energy control module contains internal interface control modules that monitor specific cell groups.
The battery energy control module will determine when a fault condition is present. Diagnostics and system status are communicated from the battery energy control module to the hybrid powertrain control module 2 through serial data. The hybrid powertrain control module 2 is the host controller for diagnostic trouble code information.
What are the Possible Causes of the DTC P3044 Buick?
- Faulty Hybrid/EV Battery Interface Control Module
- Hybrid/EV Battery Interface Control Module harness is open or shorted
- Hybrid/EV Battery Interface Control Module circuit poor electrical connection
How to Fix the DTC P3044 Buick?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P3044 Buick code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P3044 Buick code?
Need more information on how to fix the P3044 Buick code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P3044 Buick code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P3044 Buick Code
What does the OBDII code P3044 mean on a Buick?
The P3044 code indicates a problem with the Hybrid/EV Battery Interface Control Module 12 Voltage Sensor Circuit, specifically detecting a voltage higher than expected.
What are the common symptoms of the P3044 code?
Symptoms may include the check engine light or hybrid warning light, reduced fuel efficiency, limited EV mode functionality, or the vehicle entering a limp mode.
What causes the P3044 code to be triggered?
Common causes include a faulty voltage sensor, wiring issues like damaged or corroded wires, a defective hybrid/EV battery interface control module, or a software issue in the control system.
Can I continue driving with the P3044 code active?
It’s not recommended to continue driving with this code active, as it may lead to further damage to the hybrid battery system or cause the vehicle to lose power unexpectedly.
How is the P3044 code diagnosed?
A mechanic will use a scan tool to verify the code, inspect the voltage sensor and its wiring for damage, check the hybrid/EV control module, and test the battery system for irregularities.
What repairs can fix the P3044 code?
Repairs might include replacing the voltage sensor, repairing or replacing damaged wiring or connectors, updating the control module software, or replacing the hybrid/EV battery interface control module if necessary.
Is the P3044 code specific to Buick vehicles?
While the P3044 code is not exclusive to Buick, the specific interpretation and repair process may vary depending on the vehicle make and model.
Can a weak hybrid battery cause the P3044 code?
Yes, a weak or failing hybrid battery can sometimes contribute to triggering this code due to inconsistent voltage readings.
How much does it cost to fix the P3044 code on a Buick?
Repair costs can range from $150 to $1,500 or more, depending on whether the issue is a simple wiring repair or a more complex replacement of the control module or battery components.
Will clearing the P3044 code solve the problem?
Clearing the code may temporarily turn off the check engine light, but the underlying issue must be addressed to prevent the code from returning.
Discuss the causes and fixes for P3044 Buick OBDII Code
Code P3044 Buick comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
