AutoCodes – Jeep – P2706 Jeep

P2706 Jeep Code - Shift Solenoid 'F'

Quick Answer

The Transmission Control System uses six electronically controlled solenoids that allow hydraulic fluid to be applied to various friction elements (clutches), which enables the gear requested. Common causes include Dirty or Low Transmission Fluid, Faulty Shift Solenoid 'F', Shift Solenoid 'F' harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2706 Jeep indicates Shift Solenoid 'F'.
Common causes: Common causes include Dirty or Low Transmission Fluid, Faulty Shift Solenoid 'F', Shift Solenoid 'F' harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 1,451

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Dec 27, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2706 Jeep Description

The Transmission Control System uses six electronically controlled solenoids that allow hydraulic fluid to be applied to various friction elements (clutches), which enables the gear requested. The continuity of each solenoid circuit is periodically tested. Each inactive solenoid is turned on for a few milliseconds, then off. Each active solenoid is turned off for a few milliseconds, then on. This pulsing of voltage to the solenoid causes an inductive spike which can be sensed by the Transmission Control System. If an inductive spike is not sensed by the Transmission Control System during the continuity check, it is tested again. If the test fails three consecutive times, the appropriate Diagnostic Trouble Code (DTC) is set. If the solenoid test is run in response to a gear ratio or pressure switch error, one failure will result in setting the appropriate DTC.

OBDII Code P2706 Jeep - Shift Solenoid 'F' - AutoCodes.com — P2706 Jeep Code - Shift Solenoid 'F'

What does this mean?

What are the Possible Causes of the DTC P2706 Jeep?

Dirty or Low Transmission Fluid
Faulty Shift Solenoid 'F'
Shift Solenoid 'F' harness is open or shorted
Shift Solenoid 'F' circuit poor electrical connection

How to Fix the DTC P2706 Jeep?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2706 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2706 Jeep code?

Need more information on how to fix the P2706 Jeep code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2706 Jeep code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P2706 Jeep Code

1. What does the OBDII code P2706 mean on a Jeep?

P2706 indicates a problem with Shift Solenoid 'F,' which controls fluid flow in the transmission to engage specific gears.

2. What are the common symptoms of code P2706 on a Jeep?

Symptoms include harsh or erratic shifting, the transmission stuck in one gear, poor acceleration, or the Check Engine Light being illuminated.

3. What causes the P2706 code to appear on a Jeep?

Common causes include a faulty shift solenoid 'F,' low or dirty transmission fluid, damaged wiring or connectors, or a malfunctioning transmission control module (TCM).

4. Can driving with the P2706 code damage my Jeep?

Yes, driving with this code can lead to further transmission damage or unsafe driving conditions due to improper gear shifting.

5. How is the P2706 code diagnosed on a Jeep?

A mechanic will use an OBDII scanner to confirm the code, inspect the transmission fluid condition, and test the solenoid, wiring, and TCM for faults.

6. What are common fixes for the P2706 code on a Jeep?

Repairs include replacing the faulty shift solenoid 'F,' cleaning or replacing transmission fluid, repairing damaged wiring, or reprogramming/replacing the TCM.

7. How much does it cost to fix the P2706 code on a Jeep?

The cost varies but typically ranges from $150 to $400 for solenoid replacement, plus additional costs if wiring or TCM repairs are needed.

8. Can I fix the P2706 code on my Jeep myself?

If you have mechanical experience, you may replace the solenoid or check wiring connections, but complex issues like TCM failures may require professional help.

9. Is low transmission fluid a possible cause of the P2706 code?

Yes, low or dirty transmission fluid can cause solenoid malfunctions, leading to the P2706 code.

10. How can I prevent the P2706 code from occurring on my Jeep?

Regularly maintain your transmission by checking and replacing fluid as needed, and address transmission issues promptly to avoid solenoid damage.

Discuss the causes and fixes for P2706 Jeep OBDII Code

Submit a New Comment

Code P2706 Jeep comments

No comments found for this page.

Fix Your Car Smarter

Try the New AutoCodes App!

Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.