P2640 Dodge Code - Torque Management Feedback Signal 'A' High
Quick Answer
To improve shift feel, the Transmission Control Module (TCM) may request that the Engine Control Module (ECM) reduce engine torque during shift events. Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2640 Dodge indicates Torque Management Feedback Signal 'A' High.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2640 Dodge Description
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM.
A fault in the CAN will not cause the ECM to set the Diagnostic Trouble Codes (DTC). If a CAN fault occurs, other DTCs will set before this code.
The ECM set the OBDII code when the TCM receives a torque reduction failure message from the ECM.
What are the Possible Causes of the DTC P2640 Dodge?
- Faulty Engine Control Module (ECM)
- Faulty Transmission Control Module (TCM)
- Engine Control Module (ECM) software update
- Transmission Control Module (TCM) software update
- Engine Control Module (ECM) harness is open or shorted
- Engine Control Module (ECM) circuit poor electrical connection
How to Fix the DTC P2640 Dodge?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2640 Dodge code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2640 Dodge code?
Need more information on how to fix the P2640 Dodge code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2640 Dodge code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2640 Dodge Code
1. What does the OBDII code P2640 mean on a Dodge?
P2640 indicates that the Torque Management Feedback Signal 'A' is reading higher than the expected range, suggesting an issue with the signal circuit or related components.
2. What are common symptoms of the P2640 code in a Dodge?
Symptoms may include reduced engine performance, poor acceleration, the check engine light turning on, and erratic transmission behavior.
3. What causes the P2640 code to appear on a Dodge?
Common causes are a faulty torque management sensor, damaged or corroded wiring, a malfunctioning PCM, or electrical issues within the circuit.
4. How do I diagnose the P2640 code on my Dodge vehicle?
Start by scanning the vehicle with an OBDII scanner, inspecting the wiring for damage or corrosion, and testing the torque management sensor and its circuit for proper functionality.
5. Can I drive my Dodge with the P2640 code active?
Driving with this code is not recommended, as it may lead to reduced engine performance and potential damage to the engine or transmission.
6. How do I fix the P2640 code on a Dodge?
Repairs may involve replacing the torque management sensor, repairing or replacing damaged wiring, or reprogramming or replacing the PCM if it’s faulty.
7. What tools do I need to diagnose and repair the P2640 code?
You’ll need an OBDII scanner, a multimeter for testing electrical circuits, and possibly wiring repair tools or replacement parts.
8. Will clearing the code fix the P2640 issue?
Clearing the code will remove it temporarily, but it will likely return if the underlying problem isn’t resolved.
9. How much does it cost to fix the P2640 code on a Dodge?
Repair costs can vary, typically ranging from $100 to $500, depending on whether it involves sensor replacement, wiring repair, or PCM reprogramming.
10. Can a faulty PCM cause the P2640 code in a Dodge?
Yes, a malfunctioning Powertrain Control Module (PCM) can fail to process the torque management feedback signal properly, triggering the P2640 code.
Discuss the causes and fixes for P2640 Dodge OBDII Code
Code P2640 Dodge comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
