P2638 Chrysler Code - Torque Management Feedback Signal 'A' Range/Performance
Quick Answer
To improve shift feel, the Transmission Control Module (TCM) may request that the Engine Control Module (ECM) reduce engine torque during shift events. Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2638 Chrysler indicates Torque Management Feedback Signal 'A' Range/Performance.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2638 Chrysler Description
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM.
A fault in the CAN will not cause the ECM to set the Diagnostic Trouble Codes (DTC). If a CAN fault occurs, other DTCs will set before this code.
The ECM set the OBDII code when the TCM receives a torque reduction failure message from the ECM.
What are the Possible Causes of the DTC P2638 Chrysler?
- Faulty Engine Control Module (ECM)
- Faulty Transmission Control Module (TCM)
- Engine Control Module (ECM) software update
- Transmission Control Module (TCM) software update
- Engine Control Module (ECM) harness is open or shorted
- Engine Control Module (ECM) circuit poor electrical connection
How to Fix the DTC P2638 Chrysler?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2638 Chrysler code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2638 Chrysler code?
Need more information on how to fix the P2638 Chrysler code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2638 Chrysler code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2638 Chrysler Code
1. What are the common symptoms of OBDII code P2638 in a Chrysler vehicle?
- Common symptoms include rough idling, reduced engine performance, and potential stalling while driving.
2. What could be the possible causes of the Torque Management Feedback Signal 'A' Range/Performance error code (P2638) in a Chrysler?
- Possible causes may include a faulty torque management feedback sensor, issues with the wiring or connectors related to the sensor, or a problem with the powertrain control module (PCM).
3. How can I diagnose the OBDII code P2638 in my Chrysler?
- Diagnosis typically involves using an OBDII scanner to read the code, then performing a visual inspection of the sensor, wiring, and connectors. Testing the sensor's output signal may also be necessary.
4. Can driving with the P2638 code unresolved cause further damage to my Chrysler vehicle?
- Driving with this code may lead to poor engine performance and reduced fuel efficiency. It is recommended to address the issue promptly to prevent potential damage to other components.
5. Are there any DIY repair tips for fixing the Torque Management Feedback Signal 'A' Range/Performance code in a Chrysler?
- DIY repair tips may include checking and cleaning the sensor connections, ensuring the wiring is intact, and replacing the torque management feedback sensor if necessary.
6. How much does it typically cost to repair OBDII code P2638 in a Chrysler at a mechanic or dealership?
- The cost of repair can vary depending on the exact cause of the issue and labor rates, but it could range from $150 to $400, including parts and labor.
7. Is it safe to continue driving my Chrysler with the P2638 error code illuminated?
- While the vehicle may still be operable with this code, it is not recommended to drive for an extended period as it could lead to further engine issues or potential safety hazards.
8. Can resetting the OBDII code P2638 in my Chrysler temporarily resolve the issue?
- Resetting the code may temporarily turn off the check engine light, but if the underlying problem is not fixed, the code is likely to reappear after some driving cycles.
9. How long does it typically take to repair the Torque Management Feedback Signal 'A' Range/Performance error code in a Chrysler?
- The repair time can vary based on the exact cause of the issue and the availability of parts, but it may take anywhere from 1 to 3 hours to resolve the problem.
10. Will the OBDII code P2638 cause my Chrysler to fail an emissions test?
- Yes, this code can trigger a check engine light, which may result in a failed emissions test. It is advisable to address the issue before undergoing an emissions inspection.
Discuss the causes and fixes for P2638 Chrysler OBDII Code
Code P2638 Chrysler comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
