AutoCodes – Generic – P2211

P2211 Code - NOx Sensor 1 Heater Feedback Circuit Low Voltage

Quick Answer

The Nitrogen Oxides (NOx) sensors are part of the selective catalytic reduction system, a device used to reduce NOx emission on diesel engines. Common causes include Faulty Nitrogen Oxides (NOx) Sensor, Nitrogen Oxides Sensor harness is open or shorted, Nitrogen Oxides Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2211 indicates NOx Sensor 1 Heater Feedback Circuit Low Voltage.
Common causes: Common causes include Faulty Nitrogen Oxides (NOx) Sensor, Nitrogen Oxides Sensor harness is open or shorted, Nitrogen Oxides Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 16,231

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 29, 2024

Description
Possible Causes
How To Fix
Cost to Diagnose
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2211 Description

The Nitrogen Oxides (NOx) sensors are part of the selective catalytic reduction system, a device used to reduce NOx emission on diesel engines. There are two NOx sensors, one placed upstream of selective catalytic reduction, to measure inlet NOx concentration, and one placed downstream. They are connected with the control module via CAN and all the information is exchanged through it. Since it is a smart sensor, all the electrical monitoring is performed inside the sensor and only the results are sent to the Engine Control Module (ECM). Each NOx sensor contains a sensing cell, a pumping cell, and a heater. A sample of exhaust gas passes through a diffusion gap between the sensing cell and the pumping cell. The NOx sensor maintains a constant reference voltage across the sensing cell. An electronic circuit within the sensor controls the pump current through the pumping cell in order to maintain a constant voltage in the sensing cell. The amount of current required to maintain the reference voltage in the sensing cell is proportional to the concentration of NOx in the exhaust. The ECM varies the amount of diesel exhaust fluid (reductant) added by varying the reductant injector duty cycle in response to changes in engine exhaust NOx levels. The smart NOx sensors consist of two components, the NOx module and the NOx sensor element that are serviced as a unit. A circuit or performance condition with a NOx sensor is detected by the NOx sensor module. The smart NOx sensor module communicates the condition to the ECM over the serial data line. The ECM sets a DTC when a serial data message is received from the NOx sensor module. The Diagnostic Trouble Code (DTC) will be set if the ECM software detects a fault in the NOx sensor circuitry or a performance fault in the NOx sensor for greater than 2 s.

OBDII Code P2211 - NOx Sensor 1 Heater Feedback Circuit Low Voltage - AutoCodes.com — P2211 Code - NOx Sensor 1 Heater Feedback Circuit Low Voltage

What does this mean?

What are the Possible Causes of the DTC P2211?

Faulty Nitrogen Oxides (NOx) Sensor
Nitrogen Oxides Sensor harness is open or shorted
Nitrogen Oxides Sensor circuit poor electrical connection

How to Fix the DTC P2211?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2211 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2211 code?

Need more information on how to fix the P2211 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2211 code diagnosed by a professional: Find a repair shop in your area

Information for Specific Makes

P2211 Buick — NOx Sensor 1 Heater Feedback Circuit Low Voltage
P2211 Cadillac — NOx Sensor 1 Heater Feedback Circuit Low Voltage
P2211 Chevrolet — NOx Sensor 1 Heater Feedback Circuit Low Voltage
P2211 Dodge — NOx Sensor Heater Sense Circuit High Bank 1
P2211 Ford — NOx Sensor Heater Sense Circuit High Bank 1
P2211 GMC — NOx Sensor 1 Heater Feedback Circuit Low Voltage

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.