AutoCodes – Ford – P2110 2008 Ford Fusion

P2110 2008 Ford Fusion Code - Throttle Actuator Control System - Forced Limited RPM

Quick Answer

The electronic Throttle Actuator Control (TAC) is a DC motor controlled by the Powertrain Control Module (PCM). Common causes include Faulty Throttle Actuator Control (TAC) Motor, Throttle Actuator Control (TAC) Motor harness is open or shorted, Throttle Actuator Control (TAC) Motor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2110 2008 Ford Fusion indicates Throttle Actuator Control System - Forced Limited RPM.
Common causes: Common causes include Faulty Throttle Actuator Control (TAC) Motor, Throttle Actuator Control (TAC) Motor harness is open or shorted, Throttle Actuator Control (TAC) Motor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 3,409

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 05, 2019

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2110 2008 Ford Fusion Description

The electronic Throttle Actuator Control (TAC) is a DC motor controlled by the Powertrain Control Module (PCM). There are 2 designs for the TAC, parallel and inline. The parallel design has the motor under the bore parallel to the plate shaft. The motor housing is integrated into the main housing. The inline design has a separate motor housing. An internal spring is used in both designs to return the throttle plate to a default position. The default position is typically a throttle angle of 7 to 8 degrees from the hard stop angle. The closed throttle plate hard stop prevents the throttle from binding in the bore. This hard stop setting is not adjustable and is set to result in less airflow than the minimum engine airflow required at idle. The P2110 code is set when the Throttle Actuator Control (TAC) system is in the Failure Mode Effects Management (FMEM) mode of forced limited RPM.

OBDII Code P2110 2008 Ford Fusion - Throttle Actuator Control System - Forced Limited RPM - AutoCodes.com — P2110 2008 Ford Fusion Code - Throttle Actuator Control System - Forced Limited RPM

What does this mean?

What are the Possible Causes of the DTC P2110 2008 Ford Fusion?

Faulty Throttle Actuator Control (TAC) Motor
Throttle Actuator Control (TAC) Motor harness is open or shorted
Throttle Actuator Control (TAC) Motor circuit poor electrical connection
Faulty Powertrain Control Module (PCM)

How to Fix the DTC P2110 2008 Ford Fusion?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2110 2008 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2110 2008 Ford Fusion code?

Need more information on how to fix the P2110 2008 Ford Fusion code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2110 2008 Ford Fusion code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P2110 2008 Ford Fusion Code

1. What are the common symptoms of OBDII code P2110 on a 2008 Ford Fusion?

- Common symptoms include the vehicle going into a forced limited RPM mode, reduced engine power, and potential difficulty accelerating.

2. What causes the OBDII code P2110 to trigger in a 2008 Ford Fusion?

- The P2110 code is typically triggered by a fault in the throttle actuator control system, which can be caused by issues with the throttle body, wiring, or the control module.

3. How can I diagnose the OBDII code P2110 on my 2008 Ford Fusion?

- Diagnosis involves checking the throttle body for any signs of damage or malfunction, inspecting the wiring for any faults, and using a scan tool to read the trouble codes stored in the vehicle's computer.

4. Can a dirty throttle body cause the OBDII code P2110 on a 2008 Ford Fusion?

- Yes, a dirty or clogged throttle body can cause issues with the throttle actuator control system, leading to the triggering of the P2110 trouble code.

5. What are some repair tips for fixing the OBDII code P2110 on a 2008 Ford Fusion?

- Repair tips may include cleaning or replacing the throttle body, checking and repairing any damaged wiring, and resetting the throttle control module.

6. Is it safe to continue driving with the OBDII code P2110 present in a 2008 Ford Fusion?

- It is not recommended to drive with the P2110 code active, as it can lead to reduced engine power and potential safety hazards. It is best to address the issue promptly.

7. Can a DIY enthusiast fix the OBDII code P2110 on a 2008 Ford Fusion?

- Depending on the level of expertise, a DIY enthusiast may be able to address the P2110 code by cleaning or replacing the throttle body and checking the wiring connections.

8. How much does it typically cost to repair the OBDII code P2110 on a 2008 Ford Fusion?

- The cost of repairing the P2110 code can vary depending on the specific issue, but it may involve expenses for parts such as a new throttle body or wiring repairs, along with labor costs.

9. Will resetting the OBDII code P2110 on a 2008 Ford Fusion make it go away permanently?

- Resetting the code may temporarily clear the warning light, but if the underlying issue is not addressed, the code is likely to reappear once the problem is detected again.

10. How long does it take to repair the OBDII code P2110 on a 2008 Ford Fusion?

- The repair time can vary based on the exact cause of the P2110 code, but it typically takes a few hours to diagnose and fix the issue, potentially longer if parts need to be ordered.