P1710 Acura Code - First Hold Switch Circuit Fault Stuck On
Quick Answer
P1710 Acura indicates First Hold Switch Circuit Fault Stuck On. Common causes include Faulty Gear Selection Switch, Gear Selection Switch harness is open or shorted, Gear Selection Switch circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1710 Acura indicates First Hold Switch Circuit Fault Stuck On.
- Common causes
- Common causes include Faulty Gear Selection Switch, Gear Selection Switch harness is open or shorted, Gear Selection Switch circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1710 Acura Description
What are the Possible Causes of the DTC P1710 Acura?
- Faulty Gear Selection Switch
- Gear Selection Switch harness is open or shorted
- Gear Selection Switch circuit poor electrical connection
How to Fix the DTC P1710 Acura?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1710 Acura code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1710 Acura code?
Need more information on how to fix the P1710 Acura code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1710 Acura code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1710 Acura Code
1. What are the common symptoms of OBDII code P1710 in an Acura related to the First Hold Switch Circuit Fault Stuck On?
- Common symptoms include difficulty shifting gears, harsh shifting, and the inability to engage or disengage the first hold switch.
2. What are the possible causes of the First Hold Switch Circuit Fault Stuck On code (P1710) in an Acura?
- The code may be triggered by a faulty first hold switch, a malfunctioning transmission control module (TCM), or damaged wiring/connectors in the circuit.
3. How can I diagnose the First Hold Switch Circuit Fault in my Acura if I encounter code P1710?
- Diagnose the issue by checking the first hold switch operation, inspecting the wiring harness for damage, and testing the TCM for proper function using a diagnostic scanner.
4. Can I continue driving my Acura if the P1710 code for the First Hold Switch Circuit Fault is present?
- It is not recommended to drive the vehicle with this fault as it can lead to further damage to the transmission system. It's advisable to address the issue promptly.
5. How can I repair the First Hold Switch Circuit Fault Stuck On code (P1710) in my Acura?
- Repair options include replacing the faulty first hold switch, repairing damaged wiring or connectors, or reprogramming the TCM if necessary.
6. Will resetting the OBDII code P1710 clear the issue permanently in my Acura?
- Resetting the code may temporarily clear the fault, but if the underlying issue is not addressed, the code is likely to reappear. Proper diagnosis and repair are recommended.
7. Is it possible to prevent the First Hold Switch Circuit Fault Stuck On code (P1710) from occurring in the future?
- Regular maintenance and timely repair of any transmission-related issues can help prevent the recurrence of this fault code in your Acura.
8. Can a DIY enthusiast with basic automotive knowledge fix the P1710 code on an Acura themselves?
- Depending on the specific cause of the fault, a DIY enthusiast may be able to address the issue by replacing the first hold switch or repairing wiring. However, complex issues may require professional assistance.
9. How long does it typically take to repair the First Hold Switch Circuit Fault Stuck On code (P1710) in an Acura?
- The repair time can vary based on the exact cause of the fault and the expertise of the individual performing the repair. It can range from a few hours to a full day in some cases.
10. Are there any recalls or service bulletins related to the P1710 code in Acura vehicles?
- It's advisable to check with your local Acura dealership or online resources for any technical service bulletins or recalls related to the OBDII code P1710 in your specific Acura model.
Discuss the causes and fixes for P1710 Acura OBDII Code
-
replaced spark-plugs and adjusted valves. Engine service light came on-SVA light came on also and an Exclamation light came on but not blinking.
-
What model and year is your Acura? P1710 code is related to the transmission. You may have a problem with the shifter. Start by removing the center console and check the connector to the shifter.
-
That was not the code OBDIITech. The problem is now the VSA and Exclamation Mark light comes on. Did everything possible. Removed the negative for 10 minutes. that did nothing. VSA light comes on after a little while of driving.
-
I'm not sure what is the warning light, but I think you are referring to the tire pressure warning light. If the tire pressure is too low it could trigger the low pressure warning light and could affect the Vehicle Stability Assist (VSA) system.
-
I will make every effort tomorrow to bring the tire pressures where its suppose to be. I will keep you apprise.
-
2001 and yes my mechanic told me that that was the problem. A sensor is b/o right by the shifter.
-
I have a 2001 acura tl stuck in first gear. all the other gears work wat can I do
-
2003 Acura MDX code p1710 what do I have to change or fix ? Sometimes driving first to second gear trans slip rpm revs I have to stop the car so gear go in again
-
Start by checking the transmission fluid level and condition. Change fluid if necessary. If the fluid is OK, then you have to to have a transmission shop check the transmission for you.
-
How can I fix my car it's git the code p1710 an I have tried alot of things it's a 03 cl3.2
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
