P1403 Mazda Code - DPFE Hoses Reversed
Quick Answer
P1403 Mazda indicates DPFE Hoses Reversed. Common causes include DPFE Hoses Reversed. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P1403 Mazda indicates DPFE Hoses Reversed.
- Common causes
- Common causes include DPFE Hoses Reversed.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P1403 Mazda Description
How to Fix the DTC P1403 Mazda?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1403 Mazda code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1403 Mazda code?
Need more information on how to fix the P1403 Mazda code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1403 Mazda code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1403 Mazda Code
What does the OBDII code P1403 mean on a Mazda?
P1403 indicates that the Differential Pressure Feedback EGR (DPFE) hoses are reversed, leading to incorrect sensor readings for the EGR system.
What are the symptoms of code P1403 on a Mazda?
Common symptoms include poor engine performance, increased emissions, rough idling, and possibly the check engine light turning on.
What causes the P1403 code on a Mazda?
The code is typically caused by incorrect installation of DPFE sensor hoses or damaged hoses that are leaking or clogged.
Can driving with a P1403 code damage my Mazda?
While it may not cause immediate damage, prolonged driving with this code can lead to poor fuel efficiency, increased emissions, and potential harm to the EGR system.
How can I fix the P1403 code on my Mazda?
Inspect the DPFE sensor hoses for proper routing and ensure they are connected correctly. Replace damaged or clogged hoses if necessary.
Where are the DPFE sensor hoses located on a Mazda?
The DPFE sensor hoses are typically located near the EGR valve and connect to the DPFE sensor, which monitors exhaust gas pressure.
How do I know if the DPFE hoses are reversed?
If the hoses are reversed, the DPFE sensor will provide inaccurate readings, often resulting in the P1403 code and related symptoms like rough idling or poor acceleration.
Do I need special tools to fix code P1403 on a Mazda?
No special tools are typically required; you may just need basic automotive tools like pliers to inspect and re-route the hoses correctly.
Can a faulty DPFE sensor cause the P1403 code?
While the code specifically refers to reversed hoses, a faulty DPFE sensor can cause similar symptoms and should be checked if the hoses are correctly installed.
Should I clear the P1403 code after fixing the hoses on my Mazda?
Yes, once the hoses are properly routed or replaced, you can clear the code using an OBDII scanner to verify the repair was successful.
Discuss the causes and fixes for P1403 Mazda OBDII Code
Code P1403 Mazda comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
