P1400 Nissan Code - EGRC Solenoid Valve
Quick Answer
The EGRC-solenoid valve responds to signals from the Engine Control Module (ECM). Common causes include Faulty EGRC-solenoid valve, EGRC-solenoid valve harness is open or shorted, EGRC-solenoid valve electrical circuit poor connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P1400 Nissan indicates EGRC Solenoid Valve.
- Common causes
- Common causes include Faulty EGRC-solenoid valve, EGRC-solenoid valve harness is open or shorted, EGRC-solenoid valve electrical circuit poor connection.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P1400 Nissan Description
When the ECM sends an OFF signal, a plunger will then move to cut the vacuum signal.
What are the Possible Causes of the DTC P1400 Nissan?
- Faulty EGRC-solenoid valve
- EGRC-solenoid valve harness is open or shorted
- EGRC-solenoid valve electrical circuit poor connection
How to Fix the DTC P1400 Nissan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1400 Nissan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1400 Nissan code?
Need more information on how to fix the P1400 Nissan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1400 Nissan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1400 Nissan Code
1. What are the common symptoms of OBDII code P1400 in a Nissan related to the EGRC solenoid valve?
The common symptoms include rough idle, engine stalling, decreased fuel efficiency, and the illumination of the check engine light.
2. What typically causes the OBDII code P1400 in a Nissan related to the EGRC solenoid valve?
The code is often triggered by a faulty EGRC solenoid valve, a vacuum leak in the EGR system, or carbon buildup in the EGR passages.
3. How can I diagnose the EGRC solenoid valve issue causing the P1400 code in my Nissan?
You can use a scan tool to retrieve the trouble code and then visually inspect the EGRC solenoid valve and its connections for any signs of damage or malfunction.
4. Can a dirty EGR valve cause the P1400 code in a Nissan?
Yes, a dirty EGR valve can restrict the flow of exhaust gas and lead to the triggering of the P1400 code related to the EGRC solenoid valve.
5. What are some repair tips for fixing the OBDII code P1400 in a Nissan due to the EGRC solenoid valve issue?
You can start by cleaning or replacing the EGRC solenoid valve, checking and repairing any vacuum leaks in the EGR system, and cleaning out any carbon buildup in the EGR passages.
6. Is it safe to continue driving my Nissan with the OBDII code P1400 related to the EGRC solenoid valve?
It is not recommended to drive your vehicle for an extended period with this code present, as it can lead to poor engine performance and potential damage over time.
7. How much does it cost to repair the EGRC solenoid valve issue causing the P1400 code in a Nissan?
The cost of repair can vary depending on the extent of the issue and whether you choose to replace the valve yourself or have it done by a professional mechanic.
8. Can resetting the check engine light make the P1400 code go away temporarily?
Resetting the check engine light may temporarily clear the code, but it will likely reappear if the underlying issue with the EGRC solenoid valve is not addressed.
9. Will replacing the EGRC solenoid valve fix the P1400 code in my Nissan permanently?
Replacing the EGRC solenoid valve can fix the issue permanently, as long as there are no other underlying problems in the EGR system causing the code to reoccur.
10. How often should I check the EGRC solenoid valve in my Nissan to prevent the P1400 code from recurring?
It is recommended to include a visual inspection of the EGRC solenoid valve as part of your regular vehicle maintenance routine to catch any potential issues early and prevent the P1400 code from recurring.
Discuss the causes and fixes for P1400 Nissan OBDII Code
-
On you 1995 Nissan Altima, the EGR valve works with engine vacuum. The vacuum is supplied by EGR Solenoid Valve. Unfortunately there is no exact information on the service manual on how many amp it's need it to operate, but it should be less than 1 amp. considering that the solenoid valve resistance is around 1000 ohms and 12V.
-
Hello I checked the solenoid valve connector harness and it's only reading 5-7 volts, is that the reason I'm getting the code P1400 and what is the fix to this problem? Could it be Evap pressure sensor causing this because mechanic wants me to buy that part next he says that's why it's reading code p1447. I also get code p0446 but mechanic already replaced Evap canister and evap canister control valve, but I'm still getting that code P0446
-
Hello I checked the solenoid valve connector harness and it's only
reading 5-7 volts, is that the reason I'm getting the code P1400 and
what is the fix to this problem? Could it be Evap pressure sensor
causing this because mechanic wants me to buy that part next he says
that's why it's reading code p1447. I also get code p0446 but mechanic
already replaced Evap canister and evap canister control valve, but I'm
still getting that code P0446 -
What model and year is your Nissan? The Evap pressure sensor shouldn't trigger the P1400 code.
-
Hello I have a nissan quest 99 XE, I want to know where is located the solenoid valve assy (p1400)
Thanks. -
The solenoid valve is next to the throttle body. You have to remove the air filter box and hose to access the valve.
-
I have a p1400 error for Maxima 1997...reset the code last year with OBD II and drove the cycle and passed the tests. This year however, when i reset the p1400 code, it comes back on very quickly leaving the components in NOT READY status. The check engine lights come back when i start my car the 2nd time after erasing the code and drive half a block...it doesnt come on though when i do a reset and keep on driving during the first drive. Any fix to this? I dont want to spend $400 on changing the solenoid valve. Whats the correct drive cycle for Nissan Maxima 1997 GL automatic. Thanks
-
Other than the Solenoid Valve, only thing I can think of that could cause the code is the wires or connectors from the EGR valve to the Engine Control Module (ECM). Here is the Drive Pattern for your 97 Maxima
-
thx for your help... much appreciated. Just a quick a question, i have to follow the bottom graphical pattern? If i am not reading it wrong, its 2 mins idle 8-9 mins 55-60mph and series of 5 quick stops in total 20 mins of drive? Do i have to turn on the AC or heater during the first step? Where does the engine coolant temperature shows?
-
Correct on the speed. The temperature is at the bottom, 158 ° F. A/C and heater off.
-
my niec Nissan pathfinder jeep is bring black somoke I scan the car is giving me P0352 and I told you yesterday an you ask me about the year is 1997 mode pls help me what appen to the Jeep?
-
Hello, could you show me the location for the EGRC solenoid valve in a nissan sentra 95?
-
Here is the only image I got. You have to access the solenoid from underneath the vehicle. Make sure you check the EGR Solenoid hoses too.
Click here to enlarge image
Click here to enlarge image
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
