P1362 Audi Code - Ignition Circuit Cylinder 3 Short to B+
Quick Answer
The Engine Control Module (ECM) must determine if a misfire is occurring and identify the specific cylinder(s) and the severity of the misfire event and whether it is emissions relevant or catalyst damaging. Common causes include Faulty Ignition Coil Cylinder 3, Ignition Coil Cylinder 3 harness is open or shorted, Ignition Coil Cylinder 3 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1362 Audi indicates Ignition Circuit Cylinder 3 Short to B+.
- Common causes
- Common causes include Faulty Ignition Coil Cylinder 3, Ignition Coil Cylinder 3 harness is open or shorted, Ignition Coil Cylinder 3 circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1362 Audi Description
The misfire/engine roughness calculation is derived from the differences in the period duration (T) of individual increment gear segments. Each segment period consists of an angular range of 120° crank angle that starts 78° before the Top Dead Center (TDC).
If the expected period duration is greater than the permissible value a misfire fault for the particular cylinder is stored in the fault memory of the ECM. Depending on the level of misfire rate measured the control unit will illuminate the "Service Engine Soon" light, may cut off fuel to the particular cylinder, and may switch lambda operation to open-loop. All misfire faults are weighted to determine if the misfire is emissions relevant or catalyst damaging.
What are the Possible Causes of the DTC P1362 Audi?
- Faulty Ignition Coil Cylinder 3
- Ignition Coil Cylinder 3 harness is open or shorted
- Ignition Coil Cylinder 3 circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P1362 Audi?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1362 Audi code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1362 Audi code?
Need more information on how to fix the P1362 Audi code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1362 Audi code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1362 Audi Code
1. What does OBDII code P1362 mean for an Audi?
P1362 indicates an ignition circuit issue on cylinder 3, specifically a short to B+ (battery voltage).
2. What are the common symptoms of code P1362 in an Audi?
Symptoms may include engine misfires, rough idling, reduced performance, and a check engine light.
3. What causes the P1362 code in an Audi?
Common causes include damaged ignition coil wiring, a faulty ignition coil, a short to power in the circuit, or a malfunctioning engine control module (ECM).
4. Can I drive my Audi with a P1362 code?
Driving with this code can lead to engine misfires and potential damage to the catalytic converter, so it’s best to address it promptly.
5. How do you diagnose a P1362 code in an Audi?
Diagnosis involves inspecting the ignition coil and wiring for damage, testing for shorts in the circuit, and using a multimeter to check for proper voltage.
6. How do you fix code P1362 on an Audi?
Repairs may include replacing the ignition coil for cylinder 3, repairing damaged wiring, or addressing any shorts in the circuit.
7. How much does it cost to fix a P1362 code in an Audi?
Costs vary depending on the repair, but replacing an ignition coil typically costs $150–$300, including parts and labor.
8. Can a faulty spark plug cause the P1362 code in an Audi?
No, this code specifically relates to the ignition circuit wiring or coil, not the spark plug itself.
9. Will clearing the P1362 code fix the problem?
Clearing the code will turn off the check engine light temporarily, but the underlying issue must be resolved to prevent it from returning.
10. How can I prevent the P1362 code from occurring again?
Regular maintenance, inspecting ignition components for damage, and addressing wiring issues promptly can help prevent this code from recurring.
Discuss the causes and fixes for P1362 Audi OBDII Code
Code P1362 Audi comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
