P1360 Audi Code - Ignition Circuit Cylinder 2 Short to Ground
Quick Answer
The Engine Control Module (ECM) must determine if a misfire is occurring and identify the specific cylinder(s) and the severity of the misfire event and whether it is emissions relevant or catalyst damaging. Common causes include Faulty Ignition Coil Cylinder 2, Ignition Coil Cylinder 2 harness is open or shorted, Ignition Coil Cylinder 2 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1360 Audi indicates Ignition Circuit Cylinder 2 Short to Ground.
- Common causes
- Common causes include Faulty Ignition Coil Cylinder 2, Ignition Coil Cylinder 2 harness is open or shorted, Ignition Coil Cylinder 2 circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1360 Audi Description
The misfire/engine roughness calculation is derived from the differences in the period duration (T) of individual increment gear segments. Each segment period consists of an angular range of 120° crank angle that starts 78° before the Top Dead Center (TDC).
If the expected period duration is greater than the permissible value a misfire fault for the particular cylinder is stored in the fault memory of the ECM. Depending on the level of misfire rate measured the control unit will illuminate the "Service Engine Soon" light, may cut off fuel to the particular cylinder, and may switch lambda operation to open-loop. All misfire faults are weighted to determine if the misfire is emissions relevant or catalyst damaging.
What are the Possible Causes of the DTC P1360 Audi?
- Faulty Ignition Coil Cylinder 2
- Ignition Coil Cylinder 2 harness is open or shorted
- Ignition Coil Cylinder 2 circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P1360 Audi?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1360 Audi code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1360 Audi code?
Need more information on how to fix the P1360 Audi code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1360 Audi code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1360 Audi Code
What does the OBDII code P1360 mean on an Audi?
Code P1360 indicates an issue with the ignition circuit for cylinder 2, specifically a short to ground.
What are the common symptoms of code P1360 in an Audi?
Symptoms may include engine misfires, rough idle, reduced performance, and the check engine light illuminating.
What causes code P1360 in an Audi?
Common causes include damaged wiring, a faulty ignition coil, a shorted spark plug, or issues with the engine control module (ECM).
Can I drive my Audi with code P1360 active?
Driving with this code active is not recommended, as it can cause engine misfires that may lead to further damage over time.
How can I troubleshoot code P1360 on an Audi?
Inspect the wiring and connectors for cylinder 2’s ignition coil, check the ignition coil itself, and test the spark plug for damage or wear.
What tools are needed to diagnose code P1360 in an Audi?
You’ll need an OBDII scanner, a multimeter for testing electrical continuity, and basic hand tools to access ignition components.
How do I fix code P1360 in my Audi?
Repairs may include replacing damaged wiring, installing a new ignition coil or spark plug, or addressing a fault in the ECM if required.
How much does it cost to repair code P1360 in an Audi?
The cost depends on the exact repair needed, but replacing an ignition coil typically costs $100-$300, while spark plugs are around $20-$50 each.
Can code P1360 cause long-term damage to my Audi engine?
Yes, unresolved ignition issues can lead to unburned fuel damaging the catalytic converter or causing further engine problems.
What should I do if code P1360 keeps returning after repairs?
Double-check all wiring and connections, ensure quality parts were used, and consider having the ECM tested by a professional.
Discuss the causes and fixes for P1360 Audi OBDII Code
Code P1360 Audi comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
