P1342 MINI Code - Misfire During Start Cylinder 1
Quick Answer
As part of the CARB/OBD regulations, the Engine Control Module (ECM) must determine if a misfire is occurring and also identify the specific cylinder(s) and the severity of the misfire event and whether it is emissions relevant or catalyst damaging. Common causes include Faulty Spark Plug, Faulty Ignition Coil, Intake vacuum leak. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1342 MINI indicates Misfire During Start Cylinder 1.
- Common causes
- Common causes include Faulty Spark Plug, Faulty Ignition Coil, Intake vacuum leak.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1342 MINI Description
The misfire/engine roughness calculation is derived from the differences in the period duration (T) of individual increment gear segments. Each segment period consists of an angular range of 120° crank angle that starts 78° before Top Dead Center (TDC).
If the expected period duration is greater than the permissible value a misfire fault for the particular cylinder is stored in the fault memory of the ECM. Depending on the level of misfire rate measured the control unit will illuminate the "Service Engine Soon" light, may cutoff fuel to the particular cylinder and may switch lambda operation to open-loop. All misfire faults are weighted to determine if the misfire is emissions relevant or catalyst damaging.
What are the Possible Causes of the DTC P1342 MINI?
- Faulty Spark Plug
- Faulty Ignition Coil
- Intake vacuum leak
- Faulty Camshaft Position Sensor
- Ignition Coil harness is open or shorted
- Ignition Coil circuit poor electrical connection
How to Fix the DTC P1342 MINI?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1342 MINI code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1342 MINI code?
Need more information on how to fix the P1342 MINI code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1342 MINI code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1342 MINI Code
What does the OBDII code P1342 mean for a MINI?
P1342 indicates a misfire detected during the start of the engine in cylinder 1, which could affect engine performance and drivability.
What are the common symptoms of P1342 on a MINI?
Symptoms may include rough starting, poor acceleration, engine hesitation, reduced fuel efficiency, and the check engine light turning on.
What causes the P1342 code to appear on a MINI?
Common causes include a faulty ignition coil, worn spark plugs, fuel injector issues, low fuel pressure, or problems with the engine control module (ECM).
How can I diagnose the P1342 code on my MINI?
Use an OBDII scanner to confirm the code, inspect the spark plug and ignition coil for cylinder 1, check for fuel delivery issues, and test for proper compression.
Can I drive my MINI with the P1342 code active?
Driving with this code is not recommended, as it can lead to further engine damage, reduced performance, and increased emissions.
How do I fix the P1342 code on a MINI?
Repairs may include replacing the ignition coil, spark plug, or fuel injector for cylinder 1, addressing fuel pressure issues, or updating/reprogramming the ECM.
How much does it cost to repair the P1342 code on a MINI?
Repair costs vary, but common fixes like replacing a spark plug or ignition coil typically cost $100-$300, depending on parts and labor rates.
Can a dirty air filter cause the P1342 code?
While unlikely, a severely clogged air filter can contribute to engine misfires by restricting airflow, but it's not a common cause for P1342.
What tools do I need to troubleshoot the P1342 code?
Basic tools include an OBDII scanner, multimeter, spark plug socket, and compression tester for more in-depth diagnostics.
Will resetting the check engine light fix the P1342 code?
Resetting the light won't fix the underlying issue; the root cause of the misfire must be diagnosed and addressed to resolve the code.
Discuss the causes and fixes for P1342 MINI OBDII Code
Code P1342 MINI comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
