P1258 Ford Code - Pedal Correlation PDS1 and PDS2
Quick Answer
P1258 Ford indicates Pedal Correlation PDS1 and PDS2. Common causes for P1258 Ford include wiring or connector problems, a faulty related sensor or actuator, and control module or calibration issues. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1258 Ford indicates Pedal Correlation PDS1 and PDS2.
- Common causes
- Common causes for P1258 Ford include wiring or connector problems, a faulty related sensor or actuator, and control module or calibration issues.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1258 Ford Description
How to Fix the DTC P1258 Ford?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1258 Ford code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1258 Ford code?
Need more information on how to fix the P1258 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1258 Ford code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1258 Ford Code
What does the OBDII code P1258 mean for Ford vehicles?
Code P1258 indicates a pedal correlation issue between PDS1 (Pedal Position Sensor 1) and PDS2 (Pedal Position Sensor 2), signaling inconsistencies in the readings from the accelerator pedal sensors.
What are the common symptoms of P1258 in Ford vehicles?
Symptoms may include reduced engine performance, unexpected throttle behavior, limited acceleration, or the vehicle entering "limp mode."
What causes P1258 in Ford vehicles?
Common causes include faulty accelerator pedal sensors, wiring issues, connector problems, or a malfunctioning throttle position sensor.
Can the P1258 code trigger limp mode?
Yes, when the pedal sensors' correlation is compromised, the vehicle may enter limp mode to protect the engine and drivetrain.
How can I diagnose the P1258 code?
Use an OBDII scanner to confirm the code, inspect the wiring and connectors around the pedal sensors, and test the sensors for proper voltage and signal output.
Is it safe to drive with a P1258 code active?
Driving with this code is not recommended as throttle response may be unpredictable, potentially causing unsafe driving conditions.
How do I fix the P1258 code on a Ford vehicle?
Repairs may involve replacing faulty accelerator pedal sensors, repairing damaged wiring or connectors, or recalibrating the throttle system using specialized diagnostic tools.
Can a dirty throttle body cause the P1258 code?
While uncommon, a dirty or malfunctioning throttle body can indirectly affect pedal sensor correlation and trigger this code.
Do I need to replace the accelerator pedal assembly to fix P1258?
Replacing the pedal assembly is only necessary if the sensors within the assembly are defective and cannot be repaired.
How much does it cost to fix the P1258 code?
Repair costs vary but typically range from $100 to $500, depending on whether sensor replacement, wiring repairs, or throttle recalibration is needed.
Discuss the causes and fixes for P1258 Ford OBDII Code
Code P1258 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
