P0883 Dodge Code - TCM Power Input Signal High
Quick Answer
The Transmission Control Output circuit is used to supply power to the Transmission Solenoid/TRS Assembly and to the Powertrain Control Module (PCM) when in normal operating mode. Common causes include Faulty Transmission Control Relay, Faulty Transmission Solenoid Assembly, Faulty Transmission Control Module (TCM). Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0883 Dodge indicates TCM Power Input Signal High.
- Common causes
- Common causes include Faulty Transmission Control Relay, Faulty Transmission Solenoid Assembly, Faulty Transmission Control Module (TCM).
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0883 Dodge Description
After a PCM reset, (ignition switch turned to the run position, or after cranking the engine) the Transmission Control System verifies that the Transmission Output circuit is open by checking for voltage on the Transmission Output circuits before the Transmission Control System requests for the circuit to be powered up. If voltage is detected on the Transmission Output circuits before the request is sent, the DTC will set.
This DTC is set if the PCM senses greater than 3.0 volts on the Transmission Control Relay Output circuits prior to a request from the PCM to energize the Transmission Output circuits.
What are the Possible Causes of the DTC P0883 Dodge?
- Faulty Transmission Control Relay
- Faulty Transmission Solenoid Assembly
- Faulty Transmission Control Module (TCM)
- Transmission Control Module harness is open or shorted
- Transmission Control Module circuit poor electrical connection
- Faulty Powertrain Control Module (PCM)
How to Fix the DTC P0883 Dodge?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0883 Dodge code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0883 Dodge code?
Need more information on how to fix the P0883 Dodge code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0883 Dodge code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0883 Dodge Code
1. What are the common symptoms of OBDII code P0883 (TCM Power Input Signal High) in a Dodge vehicle?
- Common symptoms include the transmission going into "limp mode," difficulty shifting gears, and the Check Engine light illuminating.
2. What can cause the TCM Power Input Signal High error code in a Dodge?
- Possible causes include a faulty transmission control module (TCM), damaged wiring or connectors, a defective powertrain control module (PCM), or a short circuit.
3. How serious is the P0883 code in a Dodge vehicle?
- The P0883 code can affect the proper functioning of the transmission, leading to potential safety hazards and drivability issues. It is important to address this code promptly.
4. How can I diagnose the TCM Power Input Signal High code in my Dodge?
- Diagnosis typically involves using an OBDII scanner to retrieve the code, inspecting the TCM and PCM for any visible damage, and checking the wiring and connectors for faults.
5. What are some tips for repairing the P0883 code in a Dodge?
- Repair options may include replacing the TCM or PCM if faulty, repairing damaged wiring or connectors, and resetting the fault codes after making necessary repairs.
6. Can I drive my Dodge with the P0883 code present?
- It is not recommended to drive your Dodge with the P0883 code present, as it can lead to transmission issues and potentially compromise your safety on the road.
7. How much does it cost to fix the TCM Power Input Signal High code in a Dodge?
- The cost of fixing the P0883 code can vary depending on the specific cause of the issue, but it may involve part replacements, labor costs, and diagnostic fees.
8. Is it possible to reset the P0883 code on my Dodge without repairing the issue?
- While you can clear the code temporarily, it is not recommended to ignore the underlying problem causing the P0883 code, as it may lead to further issues down the line.
9. Can a DIY enthusiast repair the TCM Power Input Signal High code in a Dodge?
- Depending on the individual's skill level and access to tools, some DIY enthusiasts may be able to diagnose and repair the P0883 code, but professional assistance is recommended for complex issues.
10. How long does it take to fix the OBDII code P0883 in a Dodge?
- The repair time for the P0883 code can vary based on the specific cause and the extent of the repairs needed, ranging from a few hours to a full day at a repair shop.
Discuss the causes and fixes for P0883 Dodge OBDII Code
Code P0883 Dodge comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
