P0452 Subaru Code - EVAP System Pressure Sensor Low Input
Quick Answer
The Evaporative Emission System (EVAP) control system pressure sensor detects pressure in the purge line. Common causes include Faulty Evaporative Emission System (EVAP) Pressure sensor, Evaporative Emission System (EVAP) Pressure sensor harness is open or shorted, Evaporative Emission System (EVAP) Pressure sensor circuit poor electrical connection. Severity is Low - monitor the vehicle and repair when practical. The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
- What it means
- P0452 Subaru indicates EVAP System Pressure Sensor Low Input.
- Common causes
- Common causes include Faulty Evaporative Emission System (EVAP) Pressure sensor, Evaporative Emission System (EVAP) Pressure sensor harness is open or shorted, Evaporative Emission System (EVAP) Pressure sensor circuit poor electrical connection.
- Severity
- Low - monitor the vehicle and repair when practical.
- Can I drive?
- The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
Code P0452 Subaru Description
What are the Possible Causes of the DTC P0452 Subaru?
- Faulty Evaporative Emission System (EVAP) Pressure sensor
- Evaporative Emission System (EVAP) Pressure sensor harness is open or shorted
- Evaporative Emission System (EVAP) Pressure sensor circuit poor electrical connection
How to Fix the DTC P0452 Subaru?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0452 Subaru code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0452 Subaru code?
Need more information on how to fix the P0452 Subaru code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0452 Subaru code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0452 Subaru Code
1. What does the OBDII code P0452 indicate on a Subaru?
- Code P0452 indicates that the Engine Control Module (ECM) has detected a low voltage input from the Evaporative Emission Control (EVAP) system pressure sensor, suggesting a potential issue with the sensor or its circuit.
2. What are common symptoms of the P0452 code in a Subaru?
- Symptoms may include a check engine light, difficulties starting the engine, a noticeable fuel odor, decreased fuel efficiency, or no noticeable symptoms at all.
3. What could cause a P0452 code to appear on a Subaru?
- Possible causes include a faulty EVAP pressure sensor, wiring issues like shorts or opens in the sensor circuit, loose or corroded connectors, or a leak or blockage in the EVAP system.
4. How can I troubleshoot and fix code P0452 in my Subaru?
- Start by checking the electrical connections and wiring to the EVAP pressure sensor for any obvious damage or disconnections. If these are intact, test the sensor itself and replace it if necessary. Also, inspect the EVAP system for leaks or blockages.
5. Is it safe to drive a Subaru with the code P0452 triggered?
- While it might be safe to drive for a short period, it is not advisable to ignore this code. Doing so can lead to increased emissions, potential fuel economy reduction, and possibly more significant engine or EVAP system problems in the future.
6. How does a mechanic diagnose the P0452 code on a Subaru?
- A mechanic will typically start with a visual inspection of the EVAP system, checking for any signs of damage or leaks. They will then use an OBDII scanner to verify the code and may use a multimeter to test the sensor and circuitry. A smoke test might also be conducted to identify any leaks in the EVAP system.
7. Can a faulty gas cap cause the P0452 code on a Subaru?
- Yes, a loose or faulty gas cap can sometimes cause this code because it may lead to a leak in the EVAP system, which in turn affects the pressure readings by the sensor.
8. What parts are typically replaced to resolve code P0452 on a Subaru?
- The most commonly replaced part for fixing the P0452 code is the EVAP pressure sensor. However, repairs might also involve replacing or repairing any faulty wiring or connectors associated with the sensor.
9. How much does it cost to fix code P0452 in a Subaru?
- The cost can vary widely depending on the specific cause. Replacing an EVAP pressure sensor can range from $200 to $300 including parts and labor. Costs can be higher if there are additional issues like wiring repairs or if multiple components need replacement.
Discuss the causes and fixes for P0452 Subaru OBDII Code
-
Possibly the most irritating code ever. Have had it now 6 times on a 2012 Legacy. Had the sensor replaced once, replacing again. No mechanic can think of a good reason for this code to EVER appear, and are down to looking for things like spider webs in tubes. Of course, to check it means disassembling a large portion of the rear of the car [fuel tank off, etc]. But, of course, even though it apparently means nothing, EVERY damn light on the dash goes off, cruise, VDC, etc. all get turned off. For nothing. Waiting for second replacement sensor now. Stupid design. Stupid dash response. If not for this, would be a perfect car. Come on Subaru (the company, not the dealers who've all been great about it), fix this.
-
I have a 2019 Subaru Crosstrek with the same issue. I reported it to Subaru of America Customer Service to begin a safety campaign that will lead to a recall. All my lights go off like yours, and all the safety features are disabled; cruise control, eyesight assist, lane departure warning indicator, RAB, etc. Bulletin Number 09-82-23 was issued 10/02/23 for this issue.
If we press this with Subaru as a group as a safety issue, Subaru will have to address it with a recall.
Please call 1-800-782-2783 and open a case. Strength in numbers!
Thank you.
-
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
