P0441 2010 Nissan Rogue Code - Evaporative Control System Incorrect Purge Flow
Quick Answer
The Engine Control Module (ECM) tests the Evaporative Emission (EVAP) system for the following conditions: - Large and small leaks - Excess vacuum - Purge flow during non-commanded conditions - Fuel Level and Fuel Pressure sensor faults - EVAP Purge and Vent Valve faults The ECM monitors the Fuel Tank Pressure sensor in order to determine the level of vacuum/pressure in the EVAP system. Common causes include EVAP canister purge volume control solenoid valve stuck closed, EVAP control system pressure sensor and the circuit, Loose, disconnected or improper connection of rubber tube. Severity is Low - monitor the vehicle and repair when practical. The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
- What it means
- P0441 2010 Nissan Rogue indicates Evaporative Control System Incorrect Purge Flow.
- Common causes
- Common causes include EVAP canister purge volume control solenoid valve stuck closed, EVAP control system pressure sensor and the circuit, Loose, disconnected or improper connection of rubber tube.
- Severity
- Low - monitor the vehicle and repair when practical.
- Can I drive?
- The vehicle can usually be driven if no severe symptoms are present, but symptoms should be checked before extended driving.
Code P0441 2010 Nissan Rogue Description
- Large and small leaks
- Excess vacuum
- Purge flow during non-commanded conditions
- Fuel Level and Fuel Pressure sensor faults
- EVAP Purge and Vent Valve faults
The ECM monitors the Fuel Tank Pressure sensor in order to determine the level of vacuum/pressure in the EVAP system. The ECM commands both the EVAP Purge Solenoid and the EVAP Vent Valve ON when the conditions are met in order to apply an engine vacuum to the EVAP system. The ECM commands the EVAP Purge Solenoid OFF once the system has reached a predetermined level of vacuum. This test verifies if a vacuum can be achieved in the EVAP system. Failure to develop a vacuum may be caused by a large leak or a restriction.
What are the Possible Causes of the DTC P0441 2010 Nissan Rogue?
- EVAP canister purge volume control solenoid valve stuck closed
- EVAP control system pressure sensor and the circuit
- Loose, disconnected or improper connection of rubber tube
- Blocked rubber tube
- Cracked EVAP canister
- EVAP canister purge volume control solenoid valve circuit
- Accelerator pedal position sensor
- Blocked purge port
- EVAP canister vent control valve
How to Fix the DTC P0441 2010 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0441 2010 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0441 2010 Nissan Rogue code?
Need more information on how to fix the P0441 2010 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0441 2010 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0441 2010 Nissan Rogue Code
What does the OBDII code P0441 mean for my 2010 Nissan Rogue?
The P0441 code indicates that the Engine Control Module (ECM) has detected an incorrect purge flow in the evaporative emissions control system, which can lead to increased emissions.
What are the common symptoms of the P0441 code?
Common symptoms include the check engine light being illuminated, a rough idle, reduced fuel economy, or difficulty starting the engine in some cases.
What could cause the P0441 code to trigger in my Nissan Rogue?
Causes may include a faulty purge valve, a clogged or damaged EVAP system, vacuum leaks, or issues with the fuel tank pressure sensor.
How can I diagnose the P0441 code on my own?
You can start by visually inspecting the EVAP system for any obvious leaks or damage, checking the purge valve operation, and using a scan tool to monitor live data for proper operation of the system.
What are some common repairs for the P0441 code?
Common repairs include replacing the faulty purge valve, repairing or replacing damaged hoses in the EVAP system, and fixing any vacuum leaks.
Will driving with the P0441 code cause further damage to my vehicle?
While it may not cause immediate damage, ignoring the code can lead to increased emissions and potential issues with the vehicle's performance over time.
Is it safe to drive my 2010 Nissan Rogue with a P0441 code?
Yes, it is generally safe to drive, but you should address the issue as soon as possible to avoid potential emissions testing failures and reduced fuel efficiency.
How much will it cost to fix the P0441 code?
Repair costs can vary widely depending on the underlying issue, but fixes typically range from $50 to $300, depending on whether parts need to be replaced or if there are more extensive repairs needed.
Can I reset the check engine light after fixing the P0441 code?
Yes, after repairs, you can reset the check engine light using an OBDII scanner, or it may reset itself after several driving cycles if the issue is resolved.
Discuss the causes and fixes for P0441 2010 Nissan Rogue OBDII Code
Code P0441 2010 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
