P0406 Jeep Code - Exhaust Gas Recirculation Position Sensor Circuit High
Quick Answer
Early Exhaust Gas Recirculation (EGR) systems component s include and EGR Valve, and Engine Control Μodule (ECΜ) Controlled Vacuum Switch Valve or EGR Solenoid and an EGR Vacuum Μodulator. Common causes include Faulty EGR volume control solenoid valve, Carbon built up on EGR valve, EGR volume control solenoid valve harness is open or shorted. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P0406 Jeep indicates Exhaust Gas Recirculation Position Sensor Circuit High.
- Common causes
- Common causes include Faulty EGR volume control solenoid valve, Carbon built up on EGR valve, EGR volume control solenoid valve harness is open or shorted.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P0406 Jeep Description
The EGR system on recently built vehicles uses a step motor to control the flow rate of EGR from exhaust manifold. This motor has four winding phases. It operates according to the output pulse signal of the ECΜ. Two windings are turned ON and OFF in sequence. Each time an ON pulse is issued, the valve opens or closes, changing the flow rate. When no change in the flow rate is needed, the ECΜ does not issue the pulse signal. Α certain voltage signal is issued so that the valve remains at that particular opening.
What are the Possible Causes of the DTC P0406 Jeep?
- Faulty EGR volume control solenoid valve
- Carbon built up on EGR valve
- EGR volume control solenoid valve harness is open or shorted
- EGR volume control solenoid valve circuit poor electrical connection
- Faulty EGR temperature sensor and circuit
How to Fix the DTC P0406 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0406 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0406 Jeep code?
Need more information on how to fix the P0406 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0406 Jeep code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0406 Jeep Code
1. What are the common symptoms of OBDII code P0406 in a Jeep?
- Common symptoms include rough idling, engine stalling, decreased fuel efficiency, and the illumination of the Check Engine Light.
2. What does the OBDII code P0406 in a Jeep indicate?
- The code indicates a problem with the Exhaust Gas Recirculation (EGR) Position Sensor Circuit reading high voltage.
3. What are the possible causes of OBDII code P0406 in a Jeep?
- The code can be triggered by a faulty EGR position sensor, a damaged EGR valve, wiring issues in the EGR circuit, or a malfunctioning PCM.
4. How can I diagnose the OBDII code P0406 in my Jeep?
- Diagnosing the code involves inspecting the EGR system components, checking the wiring for any damage, and using a multimeter to test the EGR position sensor's voltage.
5. Can I still drive my Jeep with OBDII code P0406?
- While drivable in the short term, it is recommended to address the issue promptly to prevent further damage and potential engine performance issues.
6. How can I repair OBDII code P0406 in my Jeep?
- Repair options include replacing the EGR position sensor, cleaning or replacing the EGR valve, repairing any damaged wiring, or resetting the PCM after fixing the underlying issue.
7. Is it possible to clear the OBDII code P0406 in my Jeep without fixing the problem?
- Clearing the code without addressing the root cause will only temporarily turn off the Check Engine Light, as the issue will likely recur once the system performs its self-checks.
8. Can a DIY enthusiast fix OBDII code P0406 in a Jeep?
- Depending on your skill level and access to tools, DIY repairs such as replacing the EGR position sensor or cleaning the EGR valve can be feasible for some enthusiasts.
9. How much does it cost to repair OBDII code P0406 in a Jeep at a mechanic?
- The cost of repairs can vary based on the specific cause and the labor rates in your area, but expect to pay anywhere from $100 to $400 for parts and labor.
10. Will OBDII code P0406 cause my Jeep to fail an emissions test?
- Yes, since the code indicates a problem with the EGR system, it may cause your Jeep to fail an emissions test, as the EGR system plays a crucial role in reducing emissions.
Discuss the causes and fixes for P0406 Jeep OBDII Code
Code P0406 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
