P0335 2011 Nissan Xterra Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2011 Nissan Xterra indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2011 Nissan Xterra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2011 Nissan Xterra?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2011 Nissan Xterra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
2005 Xterra Crankshaft Position Sensor Replacement
User Submitted Video
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2011 Nissan Xterra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2011 Nissan Xterra code?
Need more information on how to fix the P0335 2011 Nissan Xterra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2011 Nissan Xterra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2011 Nissan Xterra Code
1. What are the common symptoms of OBDII code P0335 in a 2011 Nissan Xterra?
- Common symptoms include difficulty starting the vehicle, engine stalling, and rough idling.
2. What is the main cause of OBDII code P0335 in a 2011 Nissan Xterra?
- The main cause is usually a faulty or malfunctioning crankshaft position sensor.
3. How does a faulty crankshaft position sensor affect the performance of a 2011 Nissan Xterra?
- A faulty sensor can disrupt the engine's timing, leading to misfires, poor fuel efficiency, and potential engine damage.
4. Can a bad crankshaft position sensor be repaired, or does it need to be replaced in a 2011 Nissan Xterra?
- In most cases, a faulty crankshaft position sensor needs to be replaced to resolve the issue.
5. How difficult is it to replace the crankshaft position sensor in a 2011 Nissan Xterra?
- Replacing the sensor typically requires basic mechanical skills and tools. It is located near the engine's crankshaft and can be accessible from underneath the vehicle.
6. Are there any DIY tips for troubleshooting OBDII code P0335 in a 2011 Nissan Xterra?
- Before replacing the sensor, check the sensor's wiring harness for any damage or loose connections. Sometimes, the issue could be with the wiring rather than the sensor itself.
7. Can driving with OBDII code P0335 in a 2011 Nissan Xterra cause further damage to the vehicle?
- Continuing to drive with a faulty crankshaft position sensor can potentially cause damage to the engine over time, so it is recommended to address the issue promptly.
8. Is it safe to reset the OBDII code P0335 in a 2011 Nissan Xterra without fixing the underlying issue?
- Resetting the code without addressing the root cause may temporarily turn off the check engine light, but the problem will likely recur until the sensor is repaired or replaced.
9. How can a mechanic diagnose OBDII code P0335 in a 2011 Nissan Xterra?
- A mechanic can use a scan tool to read the code and perform further tests to confirm if the crankshaft position sensor is indeed the culprit.
10. What is the typical cost to repair OBDII code P0335 in a 2011 Nissan Xterra at a repair shop?
- The cost of replacing a crankshaft position sensor in a 2011 Nissan Xterra can vary but generally ranges from $100 to $300, including parts and labor.
Discuss the causes and fixes for P0335 2011 Nissan Xterra OBDII Code
Code P0335 2011 Nissan Xterra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
