P0335 2010 Nissan Sentra Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2010 Nissan Sentra indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2010 Nissan Sentra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2010 Nissan Sentra?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2010 Nissan Sentra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2010 Nissan Sentra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2010 Nissan Sentra code?
Need more information on how to fix the P0335 2010 Nissan Sentra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2010 Nissan Sentra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2010 Nissan Sentra Code
1. What are the common symptoms of OBDII code P0335 in a 2010 Nissan Sentra?
The common symptoms of OBDII code P0335 in a 2010 Nissan Sentra include engine stalling, rough idling, difficulty starting the engine, and a decrease in fuel efficiency.
2. What does OBDII code P0335 indicate in a 2010 Nissan Sentra?
OBDII code P0335 in a 2010 Nissan Sentra indicates a problem with the crankshaft position sensor circuit.
3. What are the possible causes of OBDII code P0335 in a 2010 Nissan Sentra?
Possible causes of OBDII code P0335 in a 2010 Nissan Sentra include a faulty crankshaft position sensor, damaged wiring or connectors in the sensor circuit, or issues with the engine control module (ECM).
4. How can I diagnose the crankshaft position sensor circuit issue in a 2010 Nissan Sentra?
To diagnose the crankshaft position sensor circuit issue in a 2010 Nissan Sentra, you can use a scan tool to check for OBDII codes, visually inspect the sensor and its wiring for damage, and perform electrical tests to check the sensor's functionality.
5. Can I drive my 2010 Nissan Sentra with OBDII code P0335?
It is not recommended to drive your 2010 Nissan Sentra with OBDII code P0335 as it can lead to engine performance issues and potential breakdowns.
6. How can I repair OBDII code P0335 in a 2010 Nissan Sentra?
To repair OBDII code P0335 in a 2010 Nissan Sentra, you may need to replace the crankshaft position sensor, repair any damaged wiring or connectors, or reprogram the engine control module (ECM).
7. Is it possible to reset OBDII code P0335 in a 2010 Nissan Sentra without fixing the underlying issue?
While you can clear the code temporarily, it will likely return if the underlying issue with the crankshaft position sensor circuit is not addressed.
8. Can a DIY enthusiast fix OBDII code P0335 in a 2010 Nissan Sentra?
Depending on your skill level and access to tools, a DIY enthusiast may be able to fix OBDII code P0335 in a 2010 Nissan Sentra by replacing the crankshaft position sensor or repairing the wiring themselves.
9. How much does it cost to repair OBDII code P0335 in a 2010 Nissan Sentra at a mechanic?
The cost to repair OBDII code P0335 in a 2010 Nissan Sentra at a mechanic can vary depending on the exact cause of the issue, but it typically ranges from $150 to $300.
10. Will OBDII code P0335 cause permanent damage to my 2010 Nissan Sentra if left unresolved?
If left unresolved, OBDII code P0335 can potentially cause permanent damage to your 2010 Nissan Sentra's engine due to issues with the crankshaft position sensor circuit. It is best to address the problem promptly to avoid further damage.
Discuss the causes and fixes for P0335 2010 Nissan Sentra OBDII Code
Code P0335 2010 Nissan Sentra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
