P0335 2010 Nissan Altima Sedan Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2010 Nissan Altima Sedan indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2010 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2010 Nissan Altima Sedan?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2010 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2010 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2010 Nissan Altima Sedan code?
Need more information on how to fix the P0335 2010 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2010 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2010 Nissan Altima Sedan Code
1. What are the common symptoms of OBDII code P0335 in a 2010 Nissan Altima Sedan?
- Common symptoms include engine stalling, difficulty starting the engine, and poor acceleration.
2. What is the main cause of OBDII code P0335 in a 2010 Nissan Altima Sedan?
- The main cause is usually a malfunctioning crankshaft position sensor or issues with the sensor's circuit.
3. How can I diagnose the crankshaft position sensor circuit in a 2010 Nissan Altima Sedan?
- You can diagnose the circuit by checking the sensor's wiring for damage, testing the sensor's resistance, and inspecting the sensor's connector for any issues.
4. Can a faulty crankshaft position sensor cause OBDII code P0335 in a 2010 Nissan Altima Sedan?
- Yes, a faulty crankshaft position sensor can trigger this code as it plays a crucial role in providing the engine's timing information.
5. What are the repair options for resolving OBDII code P0335 in a 2010 Nissan Altima Sedan?
- Repair options include replacing the crankshaft position sensor, repairing any damaged wiring or connectors, and clearing the trouble code.
6. Are there any DIY tips for addressing OBDII code P0335 in a 2010 Nissan Altima Sedan?
- DIY tips include ensuring the sensor is properly connected, checking for any visible damage to the sensor or its wiring, and consulting the vehicle's service manual for guidance.
7. Can driving with OBDII code P0335 in a 2010 Nissan Altima Sedan cause further damage?
- Continuing to drive with this code may lead to engine performance issues, potential stalling, and could eventually cause further damage if left unresolved.
8. How important is the crankshaft position sensor for the proper functioning of a 2010 Nissan Altima Sedan?
- The crankshaft position sensor is crucial for providing the engine control module with accurate timing information, making it essential for proper engine operation.
9. Is it safe to ignore OBDII code P0335 in a 2010 Nissan Altima Sedan?
- Ignoring this code is not recommended as it can lead to potential engine issues and safety concerns while driving.
10. How much does it typically cost to repair OBDII code P0335 in a 2010 Nissan Altima Sedan?
- Repair costs can vary depending on the extent of the issue, but generally, replacing the crankshaft position sensor can range from $100 to $300 including parts and labor.
Discuss the causes and fixes for P0335 2010 Nissan Altima Sedan OBDII Code
Code P0335 2010 Nissan Altima Sedan comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
