P0335 2008 Nissan Maxima Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2008 Nissan Maxima indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2008 Nissan Maxima Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2008 Nissan Maxima?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2008 Nissan Maxima?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2008 Nissan Maxima code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2008 Nissan Maxima code?
Need more information on how to fix the P0335 2008 Nissan Maxima code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2008 Nissan Maxima code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2008 Nissan Maxima Code
1. What are the common symptoms of OBDII code P0335 in a 2008 Nissan Maxima?
The common symptoms of code P0335 include engine stalling, rough idling, difficulty starting the engine, and a decrease in fuel efficiency.
2. What is the main cause of OBDII code P0335 in a 2008 Nissan Maxima?
The main cause of code P0335 in a 2008 Nissan Maxima is a faulty or malfunctioning crankshaft position sensor.
3. How does a faulty crankshaft position sensor affect the performance of a 2008 Nissan Maxima?
A faulty crankshaft position sensor can cause misfires, engine hesitation, and even prevent the engine from starting in a 2008 Nissan Maxima.
4. Can a bad crankshaft position sensor be repaired, or does it need to be replaced in a 2008 Nissan Maxima?
In most cases, a faulty crankshaft position sensor needs to be replaced rather than repaired in a 2008 Nissan Maxima to ensure proper functionality.
5. Are there any DIY tips for diagnosing and fixing OBDII code P0335 in a 2008 Nissan Maxima?
DIY tips for diagnosing code P0335 include checking the wiring harness for damage, testing the sensor's resistance, and ensuring proper sensor alignment during installation.
6. How much does it typically cost to replace a crankshaft position sensor in a 2008 Nissan Maxima?
The cost of replacing a crankshaft position sensor in a 2008 Nissan Maxima can vary depending on the labor rates and the quality of the sensor, but it typically ranges from $100 to $300.
7. Can driving with OBDII code P0335 present in a 2008 Nissan Maxima cause further damage to the vehicle?
Continuing to drive with code P0335 can potentially cause damage to other engine components and may result in more severe issues if left unresolved in a 2008 Nissan Maxima.
8. Is it safe to reset the OBDII code P0335 in a 2008 Nissan Maxima using a diagnostic tool?
While resetting the code may temporarily turn off the check engine light, it will not fix the underlying issue causing code P0335 in a 2008 Nissan Maxima. It is recommended to diagnose and address the root cause of the problem.
9. How long does it typically take to replace a crankshaft position sensor in a 2008 Nissan Maxima?
Replacing a crankshaft position sensor in a 2008 Nissan Maxima usually takes about 1-2 hours, depending on the accessibility of the sensor and the skill level of the person performing the replacement.
10. Can a malfunctioning crankshaft position sensor cause permanent damage to the engine of a 2008 Nissan Maxima?
A malfunctioning crankshaft position sensor can potentially cause damage to the engine if left unaddressed for an extended period, so it is important to diagnose and repair the issue promptly in a 2008 Nissan Maxima.
Discuss the causes and fixes for P0335 2008 Nissan Maxima OBDII Code
Code P0335 2008 Nissan Maxima comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
