P0335 2008 Nissan Altima Sedan Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2008 Nissan Altima Sedan indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2008 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2008 Nissan Altima Sedan?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2008 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2008 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2008 Nissan Altima Sedan code?
Need more information on how to fix the P0335 2008 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2008 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2008 Nissan Altima Sedan Code
1. What are the common symptoms of OBDII code P0335 in a 2008 Nissan Altima Sedan?
- Common symptoms include difficulty starting the vehicle, rough idling, stalling, and decreased fuel efficiency.
2. What can cause the OBDII code P0335 to trigger in a 2008 Nissan Altima Sedan?
- The main cause is a malfunctioning crankshaft position sensor or an issue with the sensor's wiring or connection.
3. How does a faulty crankshaft position sensor affect the performance of a 2008 Nissan Altima Sedan?
- A faulty sensor can lead to inaccurate engine timing, misfiring, and potentially cause the engine to stall while driving.
4. Can a DIY enthusiast replace the crankshaft position sensor in a 2008 Nissan Altima Sedan?
- Yes, replacing the sensor is a relatively straightforward task that can be done with basic tools, following a repair manual or online guides.
5. Are there any tips for diagnosing the cause of OBDII code P0335 in a 2008 Nissan Altima Sedan?
- It's recommended to perform a visual inspection of the sensor and its wiring, check for any loose connections, and use a multimeter to test the sensor's functionality.
6. Is it safe to drive a 2008 Nissan Altima Sedan with OBDII code P0335?
- It's not recommended to drive the vehicle with this code present, as it can lead to further engine issues and potential safety hazards.
7. How much does it typically cost to repair OBDII code P0335 in a 2008 Nissan Altima Sedan?
- The cost can vary depending on the labor rates and parts prices, but generally, the repair can range from $100 to $300, including parts and labor.
8. Can a faulty crankshaft position sensor cause other OBDII codes to appear in a 2008 Nissan Altima Sedan?
- Yes, a faulty sensor can cause related codes such as P0336 (Crankshaft Position Sensor A Circuit Range/Performance) or P0337 (Crankshaft Position Sensor A Circuit Low Input) to appear.
9. Will replacing the crankshaft position sensor automatically clear OBDII code P0335 in a 2008 Nissan Altima Sedan?
- After replacing the sensor, the code may need to be cleared using an OBDII scanner to reset the vehicle's computer and turn off the check engine light.
10. How long does it take to replace the crankshaft position sensor in a 2008 Nissan Altima Sedan?
- The replacement process typically takes around 1-2 hours, but this can vary based on the individual's skill level and access to tools.
Discuss the causes and fixes for P0335 2008 Nissan Altima Sedan OBDII Code
Code P0335 2008 Nissan Altima Sedan comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
